Valutazione discussione:
  • 0 voto(i) - 0 media
  • 1
  • 2
  • 3
  • 4
  • 5
DIR-456U: HSUPA 3G Router Wireless N 150
#1
Thumbs Up 
D-Link DIR-456U

[Immagine: dir456uside.jpg]

Dlink Present the new residential 3G Router for Home use the DIR-456U the successor of DIR-455
[Immagine: 100803_DIR-456_1.JPG]
[Immagine: 100803_DIR-456_2.JPG]
[Immagine: IMG_20111204_223030.jpg]

Technical Specifications (from datasheets)
GSM BAND (GSM/GPRS/EDGE)
• 850 / 900 / 1800 / 1900 MHz
• Power Class 4 (850 / 900 MHz)
• Power Class 1 (1800 / 1900 MHz)

UMTS/HSUPA BAND¹
• 900 / 1900 / 2100 MHz
• Power Class 3

STANDARDS
• 802.11n
• 802.11g
• 802.11b
• 802.3
• 802.3u

WIRELESS SECURITY
• 64/128-bit WEP (Wired Equivalent Privacy)
• WPA & WPA2 (Wi-Fi Protected Access)

FIREWALL
• Network Address Translation (NAT)
• Stateful Packet Inspection (SPI)

ANTENNA
• 3 Internal antennas

[Immagine: IMG_20111204_223014.jpg]

PORTS
• 2 x LAN (RJ-45)
• 1 x WAN (RJ-45)
• 1 x Phone (RJ-11)

USIM SLOT
• Standard 6-pin SIM card interface

DIAGNOSTIC LED
• Power
• Internet
• 3G Mode
• 3G Signal
• WLAN
• Phone
• SMS
• WPS
• LAN
• WAN

DIMENSIONS (L x W x H)
• 165 x 112 x 34 mm

Operating Temperature
• 0˚ to 40˚C (32˚ to 104˚F)

¹ Supported frequency band is dependent upon regional hardware version.

[Immagine: DIR-456U_Front.png]

Features
Support up to 7.2 Mps Upload
Support 802.11n up to 150 Mps
Support routing from broadband as primary internet connection, and 3G secondary or reverse, or single connection 3g or broadband

With ZTE MF210V 3G PCI express interface support:
WCDMA PS date rate: 384kbps DL/384kbps UL;
WCDMA CS date rate: 64kbps DL/64kbps UL;
HSDPA supports a maximum downlink date rate of 7.2Mbps;
HSUPA supports a maximum uplink date rate of 5.76Mbps;
EDGE CLASS12/GPRS CLASS12 PS are supported.
Reference: MF210 Design Guideline

Support phone calling using a classical handset pluggued in Rj11.
While accessing your 3.5G Internet connection, you will still have the ability to answer incoming mobile calls and respond to SMS messages. An RJ-11 jack allows you to attach a standard analog phone for high-quality mobile calls over a GSM network. Enjoy the comfort and convenience of your favorite office phone anywhere you go.

[Immagine: DIR-456U_Rear.png]

Other Specification
Chipset : Ralink Asic SOP RT3052 at 320 Mhz
Qty Ram : 32 Mb
Flashrom : 32 Mb NOR
Codice:
U-Boot 1.1.3 (Jan 12 2011 - 19:40:43) (ALPHA)                                  
                                                                                
SVN revision: 480                                                              
Target board: WHD-RV01                                                          
                                                                                
Board: Ralink APSoC DRAM:  32 MB                                                
config usb..                                                                    
============================================                                    
Ralink UBoot Version: 3.5.1.0                                                  
--------------------------------------------                                    
ASIC 3052_MP2 (Port5<->None)                                                    
DRAM component: 256 Mbits SDR                                                  
DRAM bus: 16 bit                                                                
Total memory: 32 MBytes                                                        
Flash component: NOR Flash                                                      
Date:Jan 12 2011  Time:19:40:43                                                
============================================                                    
icache: sets:256, ways:4, linesz:32 ,total:32768                                
dcache: sets:128, ways:4, linesz:32 ,total:16384                                
## Powering down port 0 ~ 3.                                                    
                                                                                
Please choose the operation:                                                    
   1: Load system code to SDRAM via TFTP.                                      
   2: Load system code then write to Flash via TFTP.                            
   3: Boot system code via Flash (default).                                    
   4: Entr boot command line interface.                                        
   7: Load Boot Loader code then write to Flash via Serial.                    
   9: Load Boot Loader code then write to Flash via TFTP.                      
0  ...   3: System Boot system code via Flash.  
  
## Booting image at bf050000 ...
addr:bf050000
We have SEAMA, Image Size = 3727392
Verifying Checksum ...

Uncompressing SEAMA linux.lzma ... OK

## Transferring control to Linux (at address 81f46ec0) ...

## Giving linux memsize in MB, 32

Starting kernel ...

Linux version 2.6.21 (polo@enzo) (gcc version 4.1.2) #1 Fri Dec 17 18:33:21 CST 2010

The CPU feqenuce set to 320 MHz
CPU revision is: 0001964c
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Built 1 zonelists.  Total pages: 8128

Serial Pinout:
Com Speed :57600 Bps
Data Bits: 8bit ,
Parity : None
Stop Bit : 1bit
Flow control: None
[Immagine: Serial-Console.jpg]

Documentation
Datasheet
Quick Installation Guide
User Manual

Firmware
DIR-456U A1 1.02 build 06
DIR-456U A1 1.01 build 02 (not available anymore!)

D-Link worldwide reference websites
Product page: India, Iran, Middle East, Russia
FTP: Middle East, South Africa, Russia
Technical Support: Taiwan TSD


Allegati
.rar   DIR456U_FW102b06.rar (Dimensione: 3.54 MB / Download: 140)
Cita messaggio
#2
Hi rafik23! Welcome back! Big Grin

Usually D-Link series with suffix "U" are intended to Middle East, Russia and Australia.
But we hope to see it soon in a European version!
La prima cosa da leggere in questo forum | Siti globali D-Link

Siate CHIARI SINTETICI E DETTAGLIATI altrimenti non possiamo aiutarvi!!!

N.B. Purtroppo non ho il tempo di rispondere in PVT: 1) usa un motore di ricerca; 2) usa la funzione "Cerca" del forum; 3) chiedi nel forum. GRZ!!!
Questo forum non è un centro assistenza, ma una comunità.
Prima di chiedere a NOI di risolvere il problema che hai TU, chiediti come TU puoi dare una mano a TUTTI.

Cita messaggio
#3
you can consider this like 455 and 457 firstly was published in russia and middle east and after is populated in europe , just this is an anounce for DIR-456, i have procured it from england but i think no diffrence in hardware between DIR-456 and DIR-456U and it's very new dlink product, announced in headerquarter dlink.com as residential router.
Cita messaggio
#4
@Pondera thank you for implementing the subject
Cita messaggio
#5
Thanks to you and your contribution to this forum! Big Grin
Please continue to treat this your thread! Wink
La prima cosa da leggere in questo forum | Siti globali D-Link

Siate CHIARI SINTETICI E DETTAGLIATI altrimenti non possiamo aiutarvi!!!

N.B. Purtroppo non ho il tempo di rispondere in PVT: 1) usa un motore di ricerca; 2) usa la funzione "Cerca" del forum; 3) chiedi nel forum. GRZ!!!
Questo forum non è un centro assistenza, ma una comunità.
Prima di chiedere a NOI di risolvere il problema che hai TU, chiediti come TU puoi dare una mano a TUTTI.

Cita messaggio
#6
hi Pondera i suggest this thread must be pinned
Cita messaggio
#7
My DIR456U router suddenly went dead (only power and network light showing) i want to reinstall the firmware. The question is : How can i connect my serial cable to the Tx, Rx, GND and 3.5V pins
Cita messaggio
#8
(18-05-2012, 13:00)skymaxnig Ha scritto: My DIR456U router suddenly went dead (only power and network light showing)

How did it happen?
La prima cosa da leggere in questo forum | Siti globali D-Link

Siate CHIARI SINTETICI E DETTAGLIATI altrimenti non possiamo aiutarvi!!!

N.B. Purtroppo non ho il tempo di rispondere in PVT: 1) usa un motore di ricerca; 2) usa la funzione "Cerca" del forum; 3) chiedi nel forum. GRZ!!!
Questo forum non è un centro assistenza, ma una comunità.
Prima di chiedere a NOI di risolvere il problema che hai TU, chiediti come TU puoi dare una mano a TUTTI.

Cita messaggio
#9
(18-05-2012, 16:21)Pondera Ha scritto:
(18-05-2012, 13:00)skymaxnig Ha scritto: My DIR456U router suddenly went dead (only power and network light showing)

How did it happen?
While working, it would hang then stop working, this continued till i power cycled it. it worked for a while then finally it stopped working with only power and 3G light showing...
Cita messaggio
#10
Try to reset the device by the specific rear button.
La prima cosa da leggere in questo forum | Siti globali D-Link

Siate CHIARI SINTETICI E DETTAGLIATI altrimenti non possiamo aiutarvi!!!

N.B. Purtroppo non ho il tempo di rispondere in PVT: 1) usa un motore di ricerca; 2) usa la funzione "Cerca" del forum; 3) chiedi nel forum. GRZ!!!
Questo forum non è un centro assistenza, ma una comunità.
Prima di chiedere a NOI di risolvere il problema che hai TU, chiediti come TU puoi dare una mano a TUTTI.

Cita messaggio
#11
(19-05-2012, 12:25)Pondera Ha scritto: Try to reset the device by the specific rear button.
I've tried that severally and it did not work....
Cita messaggio
#12
(19-05-2012, 17:11)skymaxnig Ha scritto:
(19-05-2012, 12:25)Pondera Ha scritto: Try to reset the device by the specific rear button.
I've tried that severally and it did not work....


hi , i'm back
@skymaxnig
have you tried recovery procedure ?
take reset and power on between 10 and 20 sec and release reset , when power led blink orange, and try to acces ton recovery mode page on http://192.168.0.1 first you must have an adress ip 192.168.0.X and 255.255.255.0 in subnet mask in your lan adapter configuration, and it must be connected on lan port not internet port or wireless in your dir-456u and here you can upload firmware again. it can been repaired with reflash. you will have a this page
[Immagine: emergency%2520room.JPG]
Cita messaggio
#13
(19-05-2012, 19:08)rafik23 Ha scritto:
(19-05-2012, 17:11)skymaxnig Ha scritto:
(19-05-2012, 12:25)Pondera Ha scritto: Try to reset the device by the specific rear button.
I've tried that severally and it did not work....


hi , i'm back
@skymaxnig
have you tried recovery procedure ?
take reset and power on between 10 and 20 sec and release reset , when power led blink orange, and try to acces ton recovery mode page on http://192.168.0.1 first you must have an adress ip 192.168.0.X and 255.255.255.0 in subnet mask in your lan adapter configuration, and it must be connected on lan port not internet port or wireless in your dir-456u and here you can upload firmware again. it can been repaired with reflash. you will have a this page
[Immagine: emergency%2520room.JPG]
Rfik23, Thanks a million. it worked....You have saved me the pain of replacing a new router.....thanks so much
Cita messaggio
#14
Well done! Big Grin
And now we also know that DIR-456U is Broadcom based as it has the typical Broadcom Emergency Room! Wink
La prima cosa da leggere in questo forum | Siti globali D-Link

Siate CHIARI SINTETICI E DETTAGLIATI altrimenti non possiamo aiutarvi!!!

N.B. Purtroppo non ho il tempo di rispondere in PVT: 1) usa un motore di ricerca; 2) usa la funzione "Cerca" del forum; 3) chiedi nel forum. GRZ!!!
Questo forum non è un centro assistenza, ma una comunità.
Prima di chiedere a NOI di risolvere il problema che hai TU, chiediti come TU puoi dare una mano a TUTTI.

Cita messaggio
#15
(20-05-2012, 13:41)skymaxnig Ha scritto:
(19-05-2012, 19:08)rafik23 Ha scritto:
(19-05-2012, 17:11)skymaxnig Ha scritto:
(19-05-2012, 12:25)Pondera Ha scritto: Try to reset the device by the specific rear button.
I've tried that severally and it did not work....


hi , i'm back
@skymaxnig
have you tried recovery procedure ?
take reset and power on between 10 and 20 sec and release reset , when power led blink orange, and try to acces ton recovery mode page on http://192.168.0.1 first you must have an adress ip 192.168.0.X and 255.255.255.0 in subnet mask in your lan adapter configuration, and it must be connected on lan port not internet port or wireless in your dir-456u and here you can upload firmware again. it can been repaired with reflash. you will have a this page
[Immagine: emergency%2520room.JPG]
Rfik23, Thanks a million. it worked....You have saved me the pain of replacing a new router.....thanks so much
Rafik23, thanks once again for your help. For future use, can you pls show me how to Reflash the Dilnk DIR456 router using a serial cable? i will realy appreciate it.....Thanks A lot
Cita messaggio
#16
okay il try to redact an article but just give me a time
Cita messaggio
#17
Portforwarding is not working on my DIR456u i have done every thing possible still not working any help.

if you can help pls i will be geatfull in Team Veiwer or any means thank.
Cita messaggio
#18
Hi Everyone,
I was using dlink dir 456u router last 2 months. It need firmware upgrade urgently.
Anyone can help me how to get new firmware from ftp site or other way.
Looking for help urgently.
Thanks.

How to get ftp site username & password?
Desperately looking for firmware upgrade.
Thanks.
Cita messaggio
#19
The old ftp Middle East & North Africa site link:

http://ftp.ftp.dlink-me.com/DLink_ME/DIR/DIR-456u/

now has been replaced by:

http://ftp.dlinkmea.com/ftp/DIR-456U/

but there isn't any firmware file to download.

You can report this lack to your local D-Link:

http://www.dlinkmea.com/contactus/feedback/

http://www.dlinkmea.com/corporate/contact/

http://www.facebook.com/DlinkEgypt

and also to:

http://tsd.dlink.com.tw/contact2008.asp

We hope rafik23 has a firmware backup so we can upload it in our forum for everyone it need. And also if you receive a firmware file from your local D-Link.
La prima cosa da leggere in questo forum | Siti globali D-Link

Siate CHIARI SINTETICI E DETTAGLIATI altrimenti non possiamo aiutarvi!!!

N.B. Purtroppo non ho il tempo di rispondere in PVT: 1) usa un motore di ricerca; 2) usa la funzione "Cerca" del forum; 3) chiedi nel forum. GRZ!!!
Questo forum non è un centro assistenza, ma una comunità.
Prima di chiedere a NOI di risolvere il problema che hai TU, chiediti come TU puoi dare una mano a TUTTI.

Cita messaggio
#20
Hello Everyone,
My problem is still not solved. I have Dlink DIR456U wireless routers at 5 locations. All routers date expired on 31-12-2012. I bought in November 2012 from local dealer. How to make its date 2013 and above? If not possible, means throw all 5 routers? It means the routers are useless after 2012 year? All my customers are desperately waiting for the date update.
Please help me to keep the routers working.
Thanks.
Cita messaggio


Vai al forum:


Utenti che stanno guardando questa discussione: 1 Ospite(i)