19 Novembre 2019, 11:15:51

DVA-5593 Modem Router VDSL2 VoIP Wireless AC2200

Aperto da bovirus, 25 Maggio 2019, 09:31:56

m4ss1

Ciao Paola, benvenuta  :)
Citazione di: Paolafont il 19 Giugno 2019, 19:23:121) tali parametri sono collegati alla mia utenza e quindi sono sempre uguali anche se si cambia il router?

Si

Citazione di: Paolafont il 19 Giugno 2019, 19:23:12sip key: corrisponde alla dizione D-Link " password"?
Si corrisponde alla password dell'account SIP

Citazione di: Paolafont il 19 Giugno 2019, 19:23:12outbound proxy: corrisponde alla dizione dlink "sip outbound proxy"?

Si

Ricordati di aggiungere il +39 prima del numero di telefono, es. +3906123456789

tummas

Ciao a tutti, ecco il log di avvio da seriale.

HELO
CPU0
PMCM
PMCS
PMCD
CODE
L1CD
MMUI
ZBBS
MAIN
5.0204patch2xpon-1.0.38-162.103
Boot Strap Register:  0x7dfffc2f
DRAM
NVRAM memcfg 0x327
MCB chksum 0xf65f52a5
DDR3-1600 CL11 256MB
Changed Byte Lane LDE
Changed Byte Lane LDE
PASS
FPS0
----
PAR1
J010
JFFS
BT10
0001
----
PAR2
J009
JFFS
BT09
1016
----
TRY1
NAN3
JFS2
RFS1
JFFS
JFS2
NAN5


Base: 5.2_04patch2xpon
CFE version 1.0.38-162.103-S for BCM963138 (32bit,SP,LE) generic
Build Date: Fri Apr  5 13:17:46 CEST 2019 (L.Fornalczyk@quantum)
Copyright (C) 2000-2015 Broadcom Corporation.

Boot Strap Register:  0x7dfffc2f
Chip ID: BCM63136_B0, ARM Cortex A9 Dual Core: 1000MHz
Total Memory: 268435456 bytes (256MB)
NAND ECC BCH-4, page size 0x800 bytes, spare size used 64 bytes
NAND flash device: , id 0xc2da block 128KB size 262144KB
pinmux table will be initialized later
pinmux table will be initialized later
pinmux table will be initialized later
pinmux table will be initialized later
pinmux table will be initialized later
pinmux table will be initialized later
pmc_init:PMC using DQM mode
Board IP address                  : 192.168.1.1:ffffff00
Host IP address                  : 192.168.1.100
Gateway IP address                :
Run from flash/host/tftp (f/h/c)  : f
Default host run file name        : vmlinux
Default host flash file name      : bcm963xx_fs_kernel
Boot delay (0-9 seconds)          : 1
Boot image (0=latest, 1=previous) : 0
Default host ramdisk file name    :
Default ramdisk store address    :
Default DTB file name            :
Board Id                          : 963138_VD5021
Number of MAC Addresses (1-64)    : 15
Base MAC Address                  : 11:22:33:44:55:66
PSI Size (1-128) KBytes          : 64
Enable Backup PSI [0|1]          : 1
System Log Size (0-256) KBytes    : 0
Auxillary File System Size Percent: 0
MC memory allocation (MB)        : 4
TM memory allocation (MB)        : 20
DHD 0 memory allocation (MB)      : 0
DHD 1 memory allocation (MB)      : 0
DHD 2 memory allocation (MB)      : 0
WLan Feature                      : 0x00
Voice Board Configuration (0-2)  : LE9642_ZSI_BB
Partition 1 Size (MB)            : 0M
Partition 2 Size (MB)            : 0M
Partition 3 Size (MB)            : 0M
Partition 4 Size (MB) (Data)      : 1M

Initalizing switch low level hardware.
pmc_switch_power_up: Rgmii Tx clock zone1 enable 0 zone2 enable 0.
Software Resetting Switch ... Done.
Waiting MAC port Rx/Tx to be enabled by hardware ...Done
Disable Switch All MAC port Rx/Tx
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from latest image (address 0x00020000, flash offset 0x00020000) ...
Verifying kernel signature...
Signature OK
Decompression LZMA Image OK!
Entry at 0x00018000
Starting program at 0x00018000
/memory = 0x10000000 bytes @ 0x0
Appending NVRAM to dtb, ret:0
Booting Linux on physical CPU 0x0
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Initializing cgroup subsys cpuacct
Linux version 4.1.45 (L.Fornalczyk@quantum) (gcc version 5.3.0 (Buildroot 2016.02-00009-ge86fef3b-dirty) ) #1 SMP PREEMPT Fri Apr 5 13:27:28 CEST 2019
CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Broadcom BCM963138
Reserved memory: phys 0x0fd00000 size 0x00300000 for adsl
Reserved memory: phys 0x0e800000 size 0x01400000 for tm
Reserved memory: phys 0x0e400000 size 0x00400000 for mc
Memory policy: Data cache writealloc
creating a MT_MEMORY_NONCACHED device at physical address of 0x0fd00000 to virtual address at 0xcfd00000 with size of 0x300000 byte for adsl
creating a MT_MEMORY_NONCACHED device at physical address of 0x0e800000 to virtual address at 0xce800000 with size of 0x1400000 byte for tm
creating a MT_MEMORY_NONCACHED device at physical address of 0x0e400000 to virtual address at 0xce400000 with size of 0x400000 byte for mc
On node 0 totalpages: 58624
free_area_init_node: node 0, pgdat c041d380, node_mem_map ce1c0000
  DMA zone: 36 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4096 pages, LIFO batch:0
  Normal zone: 540 pages used for memmap
  Normal zone: 54528 pages, LIFO batch:15
pmc_init:PMC using DQM mode
pmc_patch_63138:74 348034b 4b004b
PERCPU: Embedded 10 pages/cpu @cfcdd000 s11168 r8192 d21600 u40960
pcpu-alloc: s11168 r8192 d21600 u40960 alloc=10*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 58048
Kernel command line: console=ttyS0,115200 debug irqaffinity=0 coherent_pool=1M
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 227648K/234496K available (3154K kernel code, 271K rwdata, 536K rodata, 156K init, 261K bss, 6848K reserved, 0K cma-reserved)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000  (  4 kB)
    fixmap  : 0xffc00000 - 0xfff00000  (3072 kB)
    vmalloc : 0xd0800000 - 0xff000000  ( 744 MB)
    lowmem  : 0xc0000000 - 0xd0000000  ( 256 MB)
    modules : 0xbf000000 - 0xc0000000  (  16 MB)
      .text : 0xc0018000 - 0xc03b2c64  (3692 kB)
      .init : 0xc03b3000 - 0xc03da000  ( 156 kB)
      .data : 0xc03da000 - 0xc041de40  ( 272 kB)
      .bss : 0xc041de40 - 0xc045f3d4  ( 262 kB)
Preemptible hierarchical RCU implementation.
NR_IRQS:256
Cortex A9 MPCORE GIC init
DIST at fc01f000, CPU_IF at fc01e100
L2C: platform modifies aux control register: 0x02070000 -> 0x6a450000
L2C: DT/platform modifies aux control register: 0x02070000 -> 0x6a450000
L2C: DT/platform tries to modify or specify cache size
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 I prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 16 ways, 512 kB
L2C-310: CACHE_ID 0x410000c9, AUX_CTRL 0x6e450001
map_hw_timer_interrupt,127: interrupt_id 96
map_hw_timer_interrupt,127: interrupt_id 97
map_hw_timer_interrupt,127: interrupt_id 98
map_hw_timer_interrupt,127: interrupt_id 99
clocksource timer_cs: mask: 0x3fffffff max_cycles: 0x3fffffff, max_idle_ns: 9556302227 ns
sched_clock: 30 bits at 50MHz, resolution 20ns, wraps every 10737418230ns
console [ttyS0] enabled
Calibrating delay loop... 1980.41 BogoMIPS (lpj=990208)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
--Kernel Config--
  SMP=1
  PREEMPT=1
  DEBUG_SPINLOCK=0
  DEBUG_MUTEXES=0
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys net_cls
CPU: Testing write buffer coherency: ok
Broadcom Logger v0.1
Setting up static identity map for 0x18220 - 0x18254
Brought up 2 CPUs
SMP: Total of 2 processors activated (3971.07 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
futex hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 16
DMA: preallocated 1024 KiB pool for atomic coherent allocations
cpuidle: using governor ladder
cpuidle: using governor menu
Successfully retrieved NVRAM data from dtb
Failed to retrieve boot CFE version from dtb!
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
bcmhs_spi bcmhs_spi.1: master is unqueued, this is deprecated
skb_free_task created successfully with start budget 128
gbpm_do_work scheduled
BLOG v3.0 Initialized
BLOG Rule v1.0 Initialized
Broadcom IQoS v0.1 initialized
Broadcom GBPM v0.1 initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
Switched to clocksource timer_cs
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP: empty pfrag allocated with size 32768
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
PCI: CLS 0 bytes, default 32
jffs2: version 2.2 (NAND) (SUMMARY) (ZLIB) (LZMA) (RTIME) (c) 2001-2006 Red Hat, Inc.
io scheduler noop registered (default)
brd: module loaded
loop: module loaded
zram: Created 1 device(s)
Broadcom NAND controller (BrcmNand Controller)
mtd->oobsize=0, mtd->eccOobSize=0
NAND_CS_NAND_XOR=00000000
B4: NandSelect=40000001, nandConfig=26152300, chipSelect=0
brcmnand_read_id: CS0: dev_id=c2da9095
After: NandSelect=00000001, nandConfig=26152300
DevId c2da9095 may not be supported.  Will use config info
Spare Area Size = 16B/512B
Block size=00020000, erase shift=17
NAND Config: Reg=26152300, chipSize=256 MB, blockSize=128K, erase_shift=11
busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
ECC level changed to 4
OOB size changed to 16
BrcmNAND mfg 0 0 UNSUPPORTED NAND CHIP 256MB on CS0

Found NAND on CS0: ACC=c3840010, cfg=26152300, flashId=c2da9095, tim1=65324458, tim2=80000e54
BrcmNAND version = 0x80000700 256MB @00000000
brcmnand_scan: B4 nand_select = 00000001
brcmnand_scan: After nand_select = 00000001
handle_acc_control: default CORR ERR threshold  3 bits
ACC: 16 OOB bytes per 512B ECC step; from ID probe: 16
page_shift=11, bbt_erase_shift=17, chip_shift=28, phys_erase_shift=17
Brcm NAND controller version = 7.0 NAND flash size 256MB @10000000
ECC layout=brcmnand_oob_bch4_2k
brcmnand_scan:  mtd->oobsize=64
brcmnand_scan: oobavail=35, eccsize=512, writesize=2048
brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=4, eccbytes=7
-->brcmnand_default_bbt
brcmnand_default_bbt: bbt_td = bbt_slc_bch4_main_descr
Bad block table Bbt0 found at page 0001ffc0, version 0x01 for chip on CS0
Bad block table 1tbB found at page 0001ff80, version 0x01 for chip on CS0
brcmnand_reset_corr_threshold: default CORR ERR threshold  3 bits for CS0
nand_read_bbt: Bad block at 0x0d340000
rescanning ....
----- Contents of BBT -----
Bad block at d340000
----- END Contents of BBT -----
***** Found YAPS PartitionSplit Marker at 0x0025FF00
Creating 8 MTD partitions on "brcmnand.0":
0x000000000000-0x000000020000 : "CFE"
0x000000020000-0x000000260000 : "bootfs_1"
0x000000260000-0x000007de0000 : "rootfs_1"
0x000007f00000-0x00000fcc0000 : "upgrade"
0x00000fcc0000-0x00000fdc0000 : "conf_fs"
0x00000fdc0000-0x00000fe00000 : "conf_factory"
0x00000fe00000-0x000010000000 : "bbt"
0x000000000000-0x000010000000 : "flash"
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP Deflate Compression module registered
NET: Registered protocol family 24
i2c /dev entries driver
brcmboard registered
brcmboard: brcm_board_init entry
print_rst_status: Last RESET due to POR reset
DYING GASP IRQ Initialized and Enabled
SES: Button Interrupt 0x2 is enabled
WIFI: Button Interrupt 0x1 is enabled
SES: LED GPIO 0x8014 is enabled
Serial: BCM63XX driver $Revision: 3.00 $
Magic SysRq with Auxilliary trigger char enabled (type ^ h for list of supported commands)
ttyS0 at MMIO 0xfffe8600 (irq = 64, base_baud = 921600) is a BCM63XX
ttyS1 at MMIO 0xfffe8620 (irq = 65, base_baud = 921600) is a BCM63XX
bcm_i2c: check_sfp_i2c_device i2c bus 0 sfp detection using polling
bcm_i2c: create_sfp_polling_thread thread created
1Optical detection module loaded.
BPM: tot_mem_size=268435456B (256MB), buf_mem_size <15%> =40265310B (38MB), num of buffers=15534, buf size=2592
Broadcom BPM Module Char Driver v0.1 Registered<3004>
PCIe HCD (impl1)
  bcm963xx-pcie: found port [0] GEN2 Core Rev [3.01] with 1 Lanes
  bcm963xx-pcie: Enable GEN2 Default settings WAR on Core 0
  bcm963xx-pcie: Core [0] setting resistor calibration value to 0x8
  bcm963xx-pcie: Core [0] applying gen2 workarounds for core rev < 3.04
bcm963xx-pcie bcm963xx-pcie.0: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x90000000-0x9fffffff]
pci_bus 0000:00: root bus resource [bus 00-ff]
pci 0000:00:00.0: [14e4:6313] type 01 class 0x060400
pci 0000:00:00.0: PME# supported from D0 D3hot
PCI: bus0: Fast back to back transfers disabled
pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
pci 0000:01:00.0: [14e4:4360] type 00 class 0x028000
pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00007fff 64bit]
pci 0000:01:00.0: supports D1 D2
pci 0000:00:00.0: Checking PCIe ASPM for vendor 14e4 device 4360
PCI: bus1: Fast back to back transfers disabled
pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
pci 0000:00:00.0: BAR 8: assigned [mem 0x90000000-0x900fffff]
pci 0000:01:00.0: BAR 0: assigned [mem 0x90000000-0x90007fff 64bit]
pci 0000:00:00.0: PCI bridge to [bus 01]
pci 0000:00:00.0:  bridge window [mem 0x90000000-0x900fffff]
pcieport 0000:00:00.0: enabling device (0140 -> 0142)
  bcm963xx-pcie: found port [1] GEN2 Core Rev [3.01] with 1 Lanes
  bcm963xx-pcie: Enable GEN2 Default settings WAR on Core 1
  bcm963xx-pcie: Core [1] setting resistor calibration value to 0x8
  bcm963xx-pcie: Core [1] applying gen2 workarounds for core rev < 3.04
bcm963xx-pcie bcm963xx-pcie.1: PCI host bridge to bus 0001:00
pci_bus 0001:00: root bus resource [mem 0xa0000000-0xafffffff]
pci_bus 0001:00: root bus resource [bus 00-ff]
pci 0001:00:00.0: [14e4:6313] type 01 class 0x060400
pci 0001:00:00.0: PME# supported from D0 D3hot
PCI: bus0: Fast back to back transfers disabled
pci 0001:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
pci 0001:01:00.0: [14e4:4365] type 00 class 0x028000
pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x00007fff 64bit]
pci 0001:01:00.0: reg 0x18: [mem 0x00000000-0x007fffff 64bit]
pci 0001:01:00.0: reg 0x20: [mem 0x00000000-0x000fffff 64bit pref]
pci 0001:01:00.0: supports D1 D2
pci 0001:00:00.0: Checking PCIe ASPM for vendor 14e4 device 4365
PCI: bus1: Fast back to back transfers disabled
pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01
pci 0001:00:00.0: BAR 8: assigned [mem 0xa0000000-0xa0bfffff]
pci 0001:00:00.0: BAR 9: assigned [mem 0xa0c00000-0xa0cfffff 64bit pref]
pci 0001:01:00.0: BAR 2: assigned [mem 0xa0000000-0xa07fffff 64bit]
pci 0001:01:00.0: BAR 4: assigned [mem 0xa0c00000-0xa0cfffff 64bit pref]
pci 0001:01:00.0: BAR 0: assigned [mem 0xa0800000-0xa0807fff 64bit]
pci 0001:00:00.0: PCI bridge to [bus 01]
pci 0001:00:00.0:  bridge window [mem 0xa0000000-0xa0bfffff]
pci 0001:00:00.0:  bridge window [mem 0xa0c00000-0xa0cfffff 64bit pref]
pcieport 0001:00:00.0: enabling device (0140 -> 0142)
GACT probability NOT on
Mirror/redirect action on
u32 classifier
    input device check on
    Actions configured
gre: GRE over IPv4 demultiplexor driver
Initializing XFRM netlink socket
NET: Registered protocol family 17
NET: Registered protocol family 15
8021q: 802.1Q VLAN Support v1.8
Registering SWP/SWPB emulation handler
random: nonblocking pool is initialized
jffs2: notice: (1) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
VFS: Mounted root (jffs2 filesystem) on device 31:2.
devtmpfs: mounted
Freeing unused kernel memory: 156K
init started: BusyBox v1.17.3 (2019-04-05 13:18:34 CEST)
init: setting virtual memory limit 16777216 -1

starting pid 302, tty '': '/etc/init.d/rcS S boot'
starting pid 304, tty '/dev/ttyS0': '/bin/login'

Please press Enter to activate this console. Starting boot.sh ...
Restore passwd ....
Restore group ....
mount virtual fs...
mount: mounting none on /proc/bus/usb failed: No such file or directory
udevd (330): /proc/330/oom_adj is deprecated, please use /proc/330/oom_score_adj instead.
udev: starting version 142
Fri Apr  5 11:20:14 UTC 2019
Starting /etc/rc.d/S11services.sh ...


 --  Base System Init  [6.72]

[*] Starting Event Controller
[*] Loading Drivers and Kernel Modules
bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
Bridge firewalling registered
chipinfo: module license 'proprietary' taints kernel.
Disabling lock debugging due to kernel taint
brcmchipinfo: brcm_chipinfo_init entry
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 10
[*] Starting Configuration Load
nf_conntrack version 0.5.0 (3559 buckets, 14236 max)
starting pid 454, tty '/dev/null': 'logd'
 reporting service status with 'cmclient SET -u boot Device.X_ADB_SystemLog.[Enable=true].Enable true'
starting pid 461, tty '/dev/null': 'ledctld'
 reporting service status with 'cmclient SET -u boot Device.X_ADB_LED.[Enable=true].Enable true'
starting pid 463, tty '/dev/null': 'ec'
[*] Starting Configuration Manager (B)
Broadcom Command List Driver v1.0
tm_base_addr 0xce800000, size 20971520, tm_base_addr_phys 0x0e800000
mc_base_addr 0xce400000, size 4194304, mc_base_addr_phys 0x0e400000
RDP reserved memory has been adjusted
        TM: base_addr = 0xce700000, phys_addr = 0x0e700000, size = 17MB
        MC: base_addr = 0xce400000, phys_addr = 0x0e400000, size = 3MB

 RDP TM memory = 17MB, MC memory = 3MB : Max Possible Bufs <6826> of size <2560>; Allocating <5120> bufs; RDP enum <1>
++++Runner gso_desc_pool created successfully
bcmxtmrt: Broadcom BCM3136B0 ATM/PTM Network Device v0.9
Created XTM Rx queue 5 with size 256,Descriptor base=00c09000
Created XTM Rx queue 6 with size 256,Descriptor base=00c0b000
NBUFF v1.0 Initialized
Total # of labels = 62
Initialized fcache state
Broadcom Packet Flow Cache  Char Driver v4.0 Registered<3002>
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Broadcom Packet Flow Cache learning via BLOG enabled.
[FHW]  pktDbgLvl[0xbf34ce44]=0
[FHW]  fhw_construct:
Initialized Fcache HW accelerator layer state
flwStatsThread created. numFlwsPerPoll 546 maxFlwIdx 16383
Constructed Broadcom Packet Flow Cache v4.0
Initialized Runner Host Layer
Initialized Runner Unicast Layer
Initialized Runner L2 Unicast Layer
Initialized Runner Multicast Layer
Broadcom Packet Flow Cache HW acceleration enabled.
Enabled Runner binding to Flow Cache
Initialized Runner Protocol Layer (700)
Broadcom Runner Blog Driver Char Driver v0.1 Registered <3009>
bcmxtmcfg: bcmxtmcfg_init entry

ippt_mod_init:registering device ippt0
crossbar[0]: Allocated cb_idx=0 int_ep=2
crossbar[0]: Add cb_idx=0 ext_ep=1 GPHY:12
crossbar[0]: Add cb_idx=0 ext_ep=0 SERDES:6
crossbar Mux: connect cb_idx:0  int_ep 0 to ext_ep 4
crossbar Mux: connect cb_idx:0  int_ep 1 to ext_ep -1
crossbar Mux: connect cb_idx:0  int_ep 2 to ext_ep 0
crossbar[0]: ALL(init)
  GPHY:c:0 init
  SERDES:6:0 init
**** No optical module plugged in for sgmii interface on bus 0! ****
GPIO Pin 24 is configured as SFP MOD_ABS for module insertion detection
GPIO Pin 36 is configured as Serdes Loss Of Signal Detection
Setting SGMII Calibration value to 0x8
crossbar[0]: ALL(power_set)
  GPHY:c:0 power_set
  SERDES:6:c0417144 none
port_runner_generic_mtu_set:L1444 failed to set rdpa mtu size 2084 on port_0:0
eth0: <Int sw port: 0> <Logical : 00> MAC : 00:1F:A4:94:53:6D
    Chip Physical Port 10, Cross Bar Port 1, PHY_ID <0x0007f00c:0x0c:Internal PHY >
    Chip Physical Port  9, Cross Bar Port 0, PHY_ID <0x06180006:0x06:Serdes PHY >
eth1: <Ext sw port: 0> <Logical : 08> PHY_ID <0x0007f008:0x08:Internal PHY> MAC:00:1F:A4:94:53:6C
eth2: <Ext sw port: 1> <Logical : 09> PHY_ID <0x0007f009:0x09:Internal PHY> MAC:00:1F:A4:94:53:6C
eth3: <Ext sw port: 2> <Logical : 10> PHY_ID <0x0007f00a:0x0a:Internal PHY> MAC:00:1F:A4:94:53:6C
eth4: <Ext sw port: 3> <Logical : 11> PHY_ID <0x0007f00b:0x0b:Internal PHY> MAC:00:1F:A4:94:53:6C
i2c-bcm63000 fffebe00.i2c: Broadcom BCM96xxx I2C driver
SCSI subsystem initialized
Wifi Forwarding Driver is initialized!
Initializing WLCSM Module
WLCSM Module loaded successfully
DHD_FKB_POOL size is:1280 and entry size:2592
fkbpool address range: c8c00000 <-> c8f2a000
DHD_PKTTAG POOL size is:1280 and entry size:64
dhd_module_init in
dhd_queue_budget = 256
dhd_sta_threshold = 2048
dhd_if_threshold = 65536
no wifi platform data, skip
dhdpcie_pci_probe: chipmatch failed!! Unsupported vendor 14e4 device 4360
PCI_PROBE:  bus 1, slot 0,vendor 14E4, device 4365(good PCI location)
dhdpcie_init: can't find adapter info for this chip
pcieh 0001:01:00.0: enabling device (0140 -> 0142)
DHD: dongle ram size is set to 1835008(orig 1835008) at 0x200000
dhd:0: fw path:(null) nv path:(null)
dhd_runner_attach: Rx Offload - Enabled, Ring Size = 1024
dhd_prealloc_attach: pre-allocated buffer mode is disabled (allocskbsz=0)
dhd_attach(): thread:dhd_watchdog_thread:287 started
dhd_attach(): thread:dhd0_dpc:288 started
dhd_deferred_work_init: work queue initialized
dhd_macdbg_attach: psvmpmems caea8100 svmpmems_sz 11
Creating CPU ring for queue number 0 with 1024 packets descriptor=0xbf41875c
 Creating CPU ring for queue number 1 with 1024 packets descriptor=0xbf418778
  wfd_bind: Dev wl%d wfd_idx 0 wl_radio_idx 0 Type fkb configured WFD thread wfd0-thrd minQId/maxQId (8/9), status (0) qmask 0x3
Instantiating WFD 0 thread
dhd:0: fw path:(null) nv path:(null)
dhd_bus_download_firmware: firmware path=/etc/wlan/dhd, nvram path=
update_firmware_path: pfw_path = /etc/wlan/dhd
dhdpcie_ramsize_adj: Enter
dhd_bea_read_header: Not a .bea header
crossbar[0]: ALL(power_set)
dhdpcie_ramsize_adj: Adjust dongle RAMSIZE to 0x240000
 cm: wrong  GPHY:c:0 power_set
pathRef: Devidhdpcie_download_code_file: download firmware /etc/wlan/dhd/4366c0/rtecdc.bin
  SERDES:6:c0417144 none
ce.Services.VoiceService.1.X_DLINK_OutboundInterface: Device.IP.Interface.2
dhd_bea_read_header: Not a .bea header
-  CM TR-181 ready
-  CM TR-98 ready
[Configuration Load ready]
[*] Starting System Log
[System Log ready]
[*] Starting LEDs (B)
wl:srom/otp not programmed, using main memory mapped srom info(wombo board)
wl: ID=pci/1/1/0/
wl: ID=pci/1/1/0/
wl: loading /etc/wlan/bcm43664_map.bin
wl: updating srom from flash...
wl: reading /etc/wlan/bcmcmn_nvramvars.bin, file size=19
wl: reading /etc/wlan/bcm43664_nvramvars.bin, file size=17
Replace or append with internal Mac Address
dhdpcie_bus_write_vars: Download, Upload and compare of NVRAM succeeded.
[*] Probing for usb devices...
[*] Cleaning dynamic entries...
[*] Epicentro Software Version: DVA-5593_A1_EU_20190405
[*] Epicentro Platform Version: 7.6.2.0001
PCIe shared addr (0x002b4874) read took 65023 usec before dongle is ready
DMA RX offset from shared Area 0
dhdpcie_readshared: Dongle advertizes 2 size indices
dhdpcie_readshared: Host support DMAing indices: H2D:1 - D2H:1. FW supports it
[LEDs (B) ready]
H2D DMA WR INDX : array size 544 = 2 * 266
D2H DMA RD INDX : array size 32 = 2 * 3
D2H DMA WR INDX : array size 32 = 2 * 3
H2D DMA RD INDX : array size 544 = 2 * 266
ring_info_raw: 56
18 61 43 00 e8 71 43 00 fc 73 43 00 10 76 43 00
16 76 43 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 0a 01 00 00
dhdpcie_readshared: max H2D queues 266
dhd_bus_start: Initializing 266 h2drings
dhd_runner_profile_init: N+M profile = 3 01:1024 -1:2048 -1:1024 -1:0512 01:0512
dhd_runner_policy_init: N+M Policy = 0 1 (HW)
dhd_bus_cmn_writeshared:
  0000: 00 30 f6 0d 00 00 00 00
dhd_bus_cmn_writeshared:
  0000: 00 00 95 00 00 00 00 00
dhd_bus_cmn_writeshared:
  0000: 00 c0 72 09 00 00 00 00
dhd_bus_cmn_writeshared:
  0000: 00 00 82 08 00 00 00 00
dhd_bus_cmn_writeshared:
  0000: 00 80 95 00 00 00 00 00
dhd_bus_cmn_writeshared:
  0000: 00 00 a0 08 00 00 00 00
dhd_bus_cmn_writeshared:
  0000: 00 10 14 00
dhd_bus_cmn_writeshared:
  0000: 00 48 7f 09 00 00 00 00
dhd_bus_cmn_writeshared:
  0000: 00 4c 7f 09 00 00 00 00
dhd_bus_cmn_writeshared:
  0000: 00 40 7f 09 00 00 00 00
dhd_bus_cmn_writeshared:
  0000: 00 44 7f 09 00 00 00 00
Attach flowrings pool for 264 rings
Runner DHD PCIE: vendor<0x14e4> device<0x4365> bus<1> slot<0>
Initial configuration
=================================
        rx_post_flow_ring_base_addr : c0950000
        tx_post_flow_ring_base_addr :  (null)
        rx_complete_flow_ring_base_addr : c0958000
        tx_complete_flow_ring_base_addr :  (null)

        r2d_wr_arr_base_addr : d2889000
        d2r_rd_arr_base_addr : d2889402
        r2d_rd_arr_base_addr : d2889c00
        d2r_wr_arr_base_addr : d2889802
        tx_post_mgmt_arr_base_addr : d288a000
        tx_post_mgmt_arr_base_phys_addr : 0x97f5000

        r2d_wr_arr_base_phys_addr : 0x97f4000
        d2r_rd_arr_base_phys_addr : 0x97f4402
        r2d_rd_arr_base_phys_addr : 0x97f4c00
        d2r_wr_arr_base_phys_addr : 0x97f4802

        Doorbell ISR : bf436338
        Doorbell CTX : c962bc00
Creating CPU ring for queue number 7 with 128 packets descriptor=0xbf2fe2a0, size_of_entry 16
Done initializing Ring 7 Base=0xd0822000 End=0xd0822800 calculated entries= 128 RDD Base=c1e000K descriptor=0xbf2fe2a0
Runner DHD Offload initialization complete
CUR_ETHERADDR : 6
00 1f a4 94 53 6e
dhd_sync_with_dongle: GET_REVINFO device 0x43c5, vendor 0x14e4, chipnum 0xaa90

Dongle Host Driver, version 7.14.170.1708.cpe5.02L04.0-kdb
wfd_registerdevice Successfully registered dev wl0 ifidx 0 wfd_idx 0
dhd_module_init out
crossbar[0]: ONE(caps_get) active: SERDES:6
Broadcom 802.1Q VLAN Interface, v0.1
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
PPP MPPE Compression module registered
ipip: IPv4 over IPv4 tunneling driver
sit: IPv6 over IPv4 tunneling driver
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-platform: EHCI generic platform driver
++++ Powering up SATA block
writing PORT0_SATA3_PCB_BLOCK_ADDR
INFO: PLL lock for port0 detected 9100...
ahci ahci.0: SSS flag set, parallel bus scan disabled
ahci ahci.0: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
ahci ahci.0: flags: 64bit ncq sntf stag clo pmp slum part
scsi host0: ahci
ata1: SATA max UDMA/133 mmio [mem 0x8000a000-0x8000bfff] port 0x100 irq 77
ata1: SATA link down (SStatus 0 SControl 300)
++++ Powering up USB blocks
++++ USB POWER ON ++++
ehci-platform ehci-platform.0: EHCI Host Controller
ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
ehci-platform ehci-platform.0: irq 105, io mem 0x8000c300
ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
xt_time: kernel timezone is -0000
--SMP support
wl: dsl_tx_pkt_flush_len=338
wl: norm_wmark_tot=10097, pktc_wmark_tot=10097
wl 0000:01:00.0: enabling device (0140 -> 0142)
wl: passivemode=1
wl1: creating kthread wl1-kthrd
initvars_cis_pci: Not CIS format
sprom_read_pci: buf[0] = 0xffff, returning bad-crc
sprom_read_pci: buf[0] = 0xffff, returning bad-crc
sprom_read_pci: buf[0] = 0xffff, returning bad-crc
wl:srom/otp not programmed, using main memory mapped srom info(wombo board)
wl: ID=pci/0/1/0/
wl: ID=pci/0/1/0/
wl: loading /etc/wlan/bcm4360_map.bin
wl: updating srom from flash...
Ebtables v2.0 registered
wl: updating srom from flash...
srom rev:11
wl: reading /etc/wlan/bcmcmn_nvramvars.bin, file size=19
wl: reading /etc/wlan/bcm4360_nvramvars.bin, file size=18
wl1: allocskbmode=0 currallocskbsz=0
Creating CPU ring for queue number 2 with 1024 packets descriptor=0xbf418794
 Creating CPU ring for queue number 3 with 1024 packets descriptor=0xbf4187b0
  wfd_bind: Dev wl%d wfd_idx 1 wl_radio_idx 1 Type skb configured WFD thread wfd1-thrd minQId/maxQId (10/11), status (0) qmask 0xc
Instantiating WFD 1 thread
wfd_registerdevice Successfully registered dev wl1 ifidx 0 wfd_idx 1
wl1: Broadcom BCM4360 802.11 Wireless Controller 7.14.170.1708.cpe5.02L04.0-kdb
dgasp: kerSysRegisterDyingGaspHandler: wl1 registered
ip6_tables: (C) 2000-2006 Netfilter Core Team
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-platform: OHCI generic platform driver
ohci-platform ohci-platform.0: Generic Platform OHCI controller
ohci-platform ohci-platform.0: new USB bus registered, assigned bus number 2
ohci-platform ohci-platform.0: irq 104, io mem 0x8000c400
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
xhci-hcd xhci-hcd.0: xHCI Host Controller
xhci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 3
xhci-hcd xhci-hcd.0: hcc params 0x0250f17c hci version 0x100 quirks 0x00014010
xhci-hcd xhci-hcd.0: irq 106, io mem 0x8000d000
hub 3-0:1.0: USB hub found
hub 3-0:1.0: config failed, hub doesn't have any ports! (err -19)
[*zram0: detected capacity change from 0 to 3145728
] Starting Swap Disk xhci-hcd xhci-hcd.0: xHCI Host Controller
(RAM)
[Swap Disk (RAM) ready]
[*] hci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 4
mStarting Yatta Transport Fast Forwarding
Adding 3068k swap on /dev/zram0.  Priority:-1 extents:1 across:3068k SS
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
Loading modules backported from Linux version v4.2-rc1-0-gd770e55
Backport generated by backports.git v4.2-rc1-1-0-g83a2518
[Yatta Transport Fast Forwarding ready]
usbcore: registered new interface driver cdc_wdm
wfd_registerdevice Successfully registered dev wl0.1 ifidx 1 wfd_idx 0
starting pid 1475, tty '/dev/null': 'swmdk'
wfd_registerdevice Successfully registered dev wl1.1 ifidx 1 wfd_idx 1
VM usage warning: process swmdk (1492) req 8192 KB, total 18504 KB, limit 16384 KB
usbcore: registered new interface driver usblp
usbcore: registered new interface driver usbserial
usbcore: registered new interface driver cdc_ncm
usbcore: registered new interface driver huawei_cdc_ncm
BRCM TRNG registered
[DSPHAL] dsphal_init: Starting DSPHAL driver.
[DSPHAL] pcm_clk_init: starting PCM clock
[DSPHAL] pcm_nco_mux_cfg: using MISC for NCO FCW
[DSPHAL] pcm_nco_init: PCM clock in ZSI mode
[DSPHAL] dh_configure_channel: device 0, channel 0, id 0, devType 45, intfType 0, status 0, chanType 0, rate 8000 Hz, comp 0
[DSPHAL] pcm_ts_alloc: DMA 4 timeslot [8-bit 0, 16-bit 0] assigned to channel 0 as buffer channel 0
[DSPHAL] pcm_ts_alloc: DMA 5 timeslot [8-bit 0, 16-bit 0] assigned to channel 0 as buffer channel 0
[DSPHAL] pcm_ts_alloc: DMA 4 timeslot [8-bit 1, 16-bit 0] assigned to channel 0 as buffer channel 0
[DSPHAL] pcm_ts_alloc: DMA 5 timeslot [8-bit 1, 16-bit 0] assigned to channel 0 as buffer channel 0
[DSPHAL] dh_configure_channel: device 0, channel 1, id 1, devType 45, intfType 0, status 0, chanType 0, rate 8000 Hz, comp 0
[DSPHAL] pcm_ts_alloc: DMA 4 timeslot [8-bit 2, 16-bit 1] assigned to channel 1 as buffer channel 1
[DSPHAL] pcm_ts_alloc: DMA 5 timeslot [8-bit 2, 16-bit 1] assigned to channel 1 as buffer channel 1
[DSPHAL] pcm_ts_alloc: DMA 4 timeslot [8-bit 3, 16-bit 1] assigned to channel 1 as buffer channel 1
[DSPHAL] pcm_ts_alloc: DMA 5 timeslot [8-bit 3, 16-bit 1] assigned to channel 1 as buffer channel 1
adsl: adsl_init entry
- Init DSL Line
bcmxtmcfg: ChipId Rev-b0
bcmxtmcfg: DS xDSL G.inp Mode = DISABLED
bcmxtmcfg: xDSL G.Fast Mode = DISABLED
bcmxtmrt: PTM/ATM Non-Bonding Mode configured in system
bcmxtmcfg: Out of sequence call to XTM_ASM_HANDLER::Uninitialize().  Recovering.
bcmxtmcfg: ATM Bonding configured in system. Fallback mode = Enabled
bcmxtmcfg: Bonding State is DATA_IDLE
bcmxtmcfg: SID MODE SET to 12 BIT MODE
bcmxtmcfg: ATM Bonding Mgmt Log Area = c69f8548
[SLICSLAC] slicslac_init: Starting SLIC/SLAC driver.
BcmAdsl_Initialize=0xbfac9028, g_pFnNotifyCallback=0xbfac9000
AdslCoreSetSDRAMBaseAddr: pAddr=0x0fd00000 sdramPageAddr=0xCF800000
usbcore: registered new interface driver option
usbserial: USB Serial support registered for GSM modem (1-port)
Broadcom 63138 WatchDog Timer Driver
initialized. heartbeat=30 sec
BcmAdslCoreCalibrate: (cnt1-cnt)=0x3938319, adslCoreCyclesPerMs=999983, BCMOS_MSEC_PER_TICK =1
*** dslThread pid=1588 ***
DYING GASP IRQ Disabled
DYING GASP IRQ Enabled
AdslCoreSetSdramImageAddr: lmem2=0x10500000, pgSize=0x800000 sdramSize=0x1AF730
AdslCoreSetSdramImageAddr: lmem2(0x500000) vs ADSL_PHY_SDRAM_BIAS(0x500000); origAddr=0xCFD00000 newAddr=0xCFD00000
pSdramPHY=0xcffffff8, 0x55555555 0x55555555
AdslCoreSetSdramImageAddr: sdramPageAddr=0xcf800000, sdramImageAddr=0xcfd00000, sdramPhyImageAddr=0x10500000
*** AdslCoreSetXfaceOffset: data[0]=0xFFFFFE6F data[1]=0x190 ***
*** XfaceOffset: 0x190 => 0x190 ***
*** AdslCoreSetSdramTrueSize: data[0]=0x7775DAFF data[1]=0x888A2500 ***
*** AdslCoreSetSdramTrueSize: data[0]=0xFFDA7577 data[1]=0x258A88 ***
*** PhySdramSize got adjusted: 0x1AF730 => 0x258A88 ***
AdslCoreSharedMemInit: shareMemStart=cfffffe0 shareMemSize=685392
__AdslCoreHwReset: pAdslX=0xfc700190
__AdslCoreHwReset: pAdslX->sdramBaseAddr=0x0000d0af, pAdslX->gfcTable[]=0x0000d0cf, adslCorePhyDesc.sdramImageAddr=0xcfd00000
AdslCoreHwReset:  pLocSbSta=c77a0000 bkupThreshold=3072
AdslCoreHwReset:  AdslOemDataAddr = 0x1067B21C, time=18 ms
***BcmDiagsMgrRegisterClient: 0 ***
VersionInfo: A2pvfbH043r.d27d
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
[*] InterfaceMonitor Init
Line 0: xDSL link down
**** A2pvfbH043r.d27d ****
port_runner_generic_mtu_set:L1444 failed to set rdpa mtu size 2084 on port_0:0
[*] Starting Firewall
[Firewall ready]
[*] Starting NAT
[*] Starting Port Mapping
[Port Mapping ready]
[NAT ready]
[*] Starting QoS
[*] WAN Optical Interfaces - Power UP! (B)
[eth0] up
crossbar[0]: ALL(power_set)
  GPHY:c:0 power_set
  SERDES:6:c0417144 none
[QoS ready]
usbcore: registered new interface driver usb-storage


 --  Prepare Networking  [17.59]

- Init USB Interfaces
- Init Bridges (0)
device eth1 entered promiscuous mode
device eth2 entered promiscuous mode
device eth3 entered promiscuous mode
device eth4 entered promiscuous mode
get_port_by_if_name:L460 is not an enet dev wl0
device wl0 entered promiscuous mode
get_port_by_if_name:L460 is not an enet dev wl1
device wl1 entered promiscuous mode
get_port_by_if_name:L460 is not an enet dev wl0.1
device wl0.1 entered promiscuous mode
get_port_by_if_name:L460 is not an enet dev wl1.1
device wl1.1 entered promiscuous mode
==[br0]== 802.1D-2004  -(eth1)--(eth2)--(eth3)--(eth4)--(wl0)--(wl1)--(wl0.1)--(wl1.1)-
device br0 entered promiscuous mode


 --  Start Networking  [19.19]

starting pid 2136, tty '/dev/null': 'dns'
[*] Starting DNS client
[DNS client ready]
[*] Starting DHCP server
[*] LAN Ethernet Interfaces - Power UP! (B)
[eth1] up
[eth2] up
crossbar[0]: ONE(caps_get) active: SERDES:6
[eth3] up
[eth4] up
[*] Starting Filtering
starting pid 2193, tty '/dev/null': 'dhcps /tmp/dhcps.conf'
[Filtering ready]
[*] Starting TR-069 agent (B)
[DHCP server ready]
starting pid 2217, tty '/dev/null': 'cwmp'
[TR-069 agent (B) ready]
[*] Starting Captive Portal
[Captive Portal ready]
[*] Starting Public Pool
[Public Pool ready]
[*] Starting IPv6 services
- DHCPv6 init


 --  Start Network Services  [19.95]

[*] Starting DNS forwarder
[DNS forwarder ready]
[*] Starting IGMP proxy
[IGMP proxy ready]
[*] Starting WPS/WLAN button service (B)
Can't open device /proc/wlan_onoff
can't open device /proc/wlan_onoff
[*] Startup Software Execution Environments
[*] Starting VOIP services (B)


 --  System Ready  [20.37]

Starting /etc/rc.d/S13storageboot.sh ...
Starting /etc/rc.d/S15optical.sh ...
OK
starting pid 2503, tty '/dev/null': 'inetd -f'
starting pid 2504, tty '/dev/null': 'mcpd'
crossbar[0]: ONE(caps_get) active: SERDES:6
OK
Starting /etc/rc.d/S17hostapd.sh ...
starting pid 2688, tty '/dev/null': 'httpd -u nobody'
br0: port 6(wl1) entered forwarding state
get_port_by_if_name:L460 is not an enet dev wl1
br0: port 6(wl1) entered forwarding state
get_port_by_if_name:L460 is not an enet dev wl1
br0: port 5(wl0) entered forwarding state
get_port_by_if_name:L460 is not an enet dev wl0
br0: port 5(wl0) entered forwarding state
get_port_by_if_name:L460 is not an enet dev wl0
rpcal2g=0x0 rpcal5gb0=0xdd71 rpcal5gb1=0xda6a rpcal5gb2=0xf77b rpcal5gb3=0x579
rpcal2gcore3=0x0 rpcal5gb0core3=0x65 rpcal5gb1core3=0x64 rpcal5gb2core3=0x81 rpcal5gb3core3=0x8a
Starting /etc/rc.d/S18acsd.sh ...
Starting /etc/rc.d/S19bsd.sh ...
Starting /etc/rc.d/S20voip.sh ...
starting pid 2821, tty '/dev/null': 'hostapd -B /tmp/wlan/config/hostapd.conf.wl0 /tmp/wlan/config/hostapd.conf.wl1 -P /var/r
starting pid 2842, tty '/dev/null': 'acsd'
Starting /etc/rc.d/S60ipsec.sh ...
Starting /etc/rc.d/S70vpn.sh ...
Starting /etc/rc.d/S94printkd.sh ...
[*] Starting Printk Dump
[Printk Dump ready]
Starting /etc/rc.d/S95done ...
Starting /etc/rc.d/S98rngd ...
starting pid 2903, tty '/dev/null': 'voip >/dev/console'
1554463241:264078 [1 voip] VOIP BASE - Start  Provisioning Endpoint Configuration
1554463241:289168 [1 voip] VOIP BASE - Completed Start Provisioning Endpoint
1554463241:289236 [1 voip] VOIP BASE - Num media profiles 16 VS num channels 10
1554463241:299204 [1 voip] VOIP BASE - Init PhoneBook Linked List
1554463241:299242 [1 voipVM usage warning: process voip (2903) req 8192 KB, total 21620 KB, limit 14336 KB
] VOIP BASE - Init Line Setting Linked List
[DSPHAL] iudma_configure: installed irq handler for interrupt 148
[DSPHAL] dh_reg_tick_source: new owner IUDMA, rate 5ms
VM usage warning: process voip (2903) req 8192 KB, total 29812 KB, limit 14336 KB
[SLICSLAC] zarlinkInit: Initializing Le9642 device 0...
[SLICSLAC] ss_device_reset: Reset applied on GPIO pin 255
[SLICSLAC] slicLe9642Init: Starting device and line initialization...
[SLICSLAC] slicLe9642Init: configured for buck-boost board
[SLICSLAC] zarlinkInitDeviceCommon: Initializing device 0
[SLICSLAC] zarlinkInitDeviceCommon: device 0 initialized.
[SLICSLAC] zarlinkInitLinesCommon: Locale set to 1
[SLICSLAC] zarlinkInitLinesCommon: Initializing FXS line 0
[SLICSLAC] zarlinkInitLinesCommon: FXS line 0 initialized.
[SLICSLAC] zarlinkInitLinesCommon: Initializing FXS line 1
[SLICSLAC] zarlinkInitLinesCommon: FXS line 1 initialized.
[SLICSLAC] zarlinkInit: Completed initialization for Le9642 device 0
dgasp: kerSysRegisterDyingGaspHandler: slicslac registered

m4ss1

21 Giugno 2019, 11:00:18 #22 Ultima modifica: 21 Giugno 2019, 11:15:17 di m4ss1
DVA-5593 Configurazione Print Server

Effettuare il login e accedere al menu nascosto
http://192.168.1.1/ui/dboard/printers

Effettuare l'accesso al forum per visualizzare gli allegati.
Non puoi visualizzare gli allegati in questa sezione.

Cliccare su configurazione di stampa e attivare il servizio di stampa

Non puoi visualizzare gli allegati in questa sezione.

Cliccare su Server di Stampa e abilitare la condivisione con MS Windows

Non puoi visualizzare gli allegati in questa sezione.

bovirus

Per chi fosse interessato il DVA-5593 è in vendita (offerta volantino) da MediaWorld a 129 euro.

falk

28 Luglio 2019, 23:29:46 #24 Ultima modifica: 28 Luglio 2019, 23:37:19 di falk
Questo router permette di utilizzare più di 2 profili Voip (multi provider) con possibilità  di creare regole di uscita e di ingresso a seconda del numero selezionato o chiamata in arrivo, oppure è "stupido" come la maggior parte degli altri prodotti (profilo 1 -> linea 1) e (profilo 2 -> linea 2) ?

m4ss1

Citazione di: falk il 28 Luglio 2019, 23:29:46Questo router permette di utilizzare più di 2 profili Voip (multi provider) con possibilità  di creare regole di uscita e di ingresso a seconda del numero selezionato o chiamata in arrivo
Ciao, no... non è possibile.

RobertaO

Ciao :-)

avrei bisogno di un piccolo aiuto. Ho una connessione ADSL Fastweb, ho collegato il DVA-5593 alla corrente e ho inserito il cavo DSL (quello grigio) al router (ingresso grigio) e alla presa a muro, perdonate il linguaggio poco tecnico ma sono inesperta. Si accendono 4 luci tranne quella di Internet e in pratica non riesco a collegarmi.

Ho il dubbio che questo router non sia compatibile con l'ADSL di Fastweb, potrebbe essere? Oppure ho sbagliato nella configurazione iniziale che però non riesco più a rifare?

Moltissime grazie,
Roberta

bovirus

@RobertaO

Per favore nei post cerca di essere il più dettagliata possibile.
Questo è fondamentale per capire e cercare di fornirti un aiuto.

Che modem avevi prima di questo D-LINK?
La linea ADSL è attiva?
L'impianto è a posto?
Quale tipo di configurazione hai effettuato e come?


tummas

@RobertaO
Ciao, dopo aver collegato i cavi e acceso il router devi configurarlo.
Apri Chrome o il browser che preferisci e vai su http://192.168.1.1
Al termine della configurazione guidata, se la linea è attiva, dovresti avere internet.

RobertaO

@bovirus - scusa per le imprecisioni e grazie per la risposta.

Prima del D-LINK avevo un modem di Fastweb del 2011 che mi hanno dato quando ho messo Internet a casa e che adesso ha un collegamento obsoleto e poco sicuro, per questo lo cambio. L'ADSL funziona, l'impianto è a posto, nella configurazione credo di aver sbagliato perchè ho messo VCI 48 anzichè 36, poi VPI 8, incapsulamento LLC.
Stasera riprovo a collegare il router e spero mi riproponga di fare la configurazione, mi spiace ma è tutto un po' complicato.
Grazie mille

RobertaO

@tummas - molte grazie per la risposta. Stasera provo a entrate nell'http che hai scritto. Buona giornata

bovirus

@RobertaO

Con il modem acceso tieni premuto con una graffetta il pulsante RESET dietro del modem per una decina di secondi.

Il modem si resetterà e sarà come lo hai appena acceso la prima volta.

Accedi via browser a 192.168.1.1 e ripeti la configurazione mettendo i parametri necessari.



enrico11111

scusate la domanda forse sciocca... ho provato in vari modi usando la configurazione avanzata a cambiare i DNS della mia linea fttc TIM con quelli di google ma nella schermata dove c'è il riepilogo dei dati vedo sempre
85.38.28.1
85.38.28.0

chi mi illumina?

.fega.

Ciao, sicuramente stai guardando i dati della connessione WAN ed è normale avere i DNS TIM
Se cambi i DNS potresti avere problemi con il VoIP.

enrico11111

Citazione di: .fega. il 14 Settembre 2019, 08:39:20Ciao, sicuramente stai guardando i dati della connessione WAN ed è normale avere i DNS TIM
Se cambi i DNS potresti avere problemi con il VoIP.

ciao e grazie per la risposta!
non uso voip quindi per quello non avrei problemi in tutti i casi !


ho cambiato i valori in Home>>Configurazione>>DNS>>Client:
il mio scopo era capire come usare i dns di google e dopo di ciò inserire al posto di essi l'indirizzo IP di un mio server locale

ma monitorando il mio server locale nessun dispositivo passa di li A MENO CHE io non tolga il dhcp e specifichi esplicitamente il DNS

questo mi fa capire che se in dhcp il router non passa il mio dns ne ovviamente quelli di google

enrico11111

Aggiungo che ho provato anche ad inserire dns statici qui :  Home>>Configurazione>>Connessioni di Rete>>Interfaccia IP>>IPv4
ma stesso risultato di prima


quello che vorrei fare io è : tutti i dispositivi (ne ho oltre 20) in DHCP (quindi ip automatico e ip del router come dns) e vorrei che ogni richiesta che arriva al server dns (router quindi) passi dai dns di goole/mio IP statico

m4ss1

15 Settembre 2019, 12:18:39 #36 Ultima modifica: 15 Settembre 2019, 12:21:57 di m4ss1
Ciao Enrico,
Citazione di: enrico11111 il 14 Settembre 2019, 09:22:21ho cambiato i valori in Home>>Configurazione>>DNS>>Client:
Devi cambiare anche il DNS Relay

Se vuoi il server DHCP può assegnare i DNS che preferisci
Server DHCP e modifica la voce "Name servers"
In questo caso puoi anche disattivare il DNS Relay

enrico11111

Citazione di: m4ss1 il 15 Settembre 2019, 12:18:39Ciao Enrico,Devi cambiare anche il DNS Relay

Se vuoi il server DHCP può assegnare i DNS che preferisci
Server DHCP e modifica la voce "Name servers"
In questo caso puoi anche disattivare il DNS Relay

ciao e intanto grazie per la risposta! il Relay l'avevo già modificato (o meglio credo che l'abbia fatto in automatico) ma il mio IP (192.168.1.10) non rileva client connessi

provo a modificare quella voce del DHCP; adesso in automatico c'era 192.168.1.1

enrico11111

l'ho lasciato in DNS client e relay
e ho fatto la modifica che hai scritto te sopra

adesso ho N device collegati! non tutti ma è già un bel traguardo ! grazie per la dritta :)

PS: dovevo togliere da client e relay il mio IP ? potrebbe crear problemi la configurazione attuale?

m4ss1

Citazione di: enrico11111 il 15 Settembre 2019, 15:25:21adesso ho N device collegati! non tutti ma è già un bel traguardo ! grazie per la dritta
Di niente, figurati ;)
Prova a disconnettere e riconnettere i dispositivi vedrai che prenderanno i nuovi DNS.

Citazione di: enrico11111 il 15 Settembre 2019, 15:25:21PS: dovevo togliere da client e relay il mio IP ? potrebbe crear problemi la configurazione attuale?

No nessun problema, puoi lasciarlo.

Licenza Creative Commons
Il contenuto dei messaggi del forum è distribuito con
Licenza Creative Commons Attribuzione Non commerciale 4.0
Tutti i marchi registrati citati appartengono ai legittimi proprietari