Menu principale

DAP-1325 Range Extender Wi‑Fi N300

Aperto da m4ss1, 11 Luglio 2019, 10:28:47

m4ss1

D-Link DAP-1325
Range Extender Wi-Fi N300


DAP-1325 (MediaTek MT7628NN)


Descrizione
Il Range Extender Wi-Fi N300 DAP-1325 è un adattatore plug-in portatile che permette di aumentare la copertura della rete wireless esistente. Basta collocarlo ovunque in casa per aumentare la portata della rete wireless.

Caratteristiche
Facile da configurare
Premi il pulsante per la configurazione WPS one-touch, premi il pulsante WPS sul tuo dispositivo Wi-Fi esistente: fatto! Il DAP-1325 si configurerà da solo automaticamente.
In alternativa, è possibile usare la app QRS Mobile sul proprio device iOS o Android per poter configurare facilmente e senza bisogno di un computer il DAP-1325.
Il Range Extender Wi-Fi N300 include anche una procedura di configurazione integrata per un controllo di maggior precisione delle impostazioni cablate e wireless.

Aumenta la copertura del tuo WI-FI
Il Range Extender Wi-Fi N300 DAP-1325 è un adattatore plug-in portatile che permette di aumentare la copertura della rete wireless esistente.
Basta collocarlo ovunque in casa per aumentare la portata della rete wireless.

Indicatore visivo del segnale
Inseriscilo e usa il LED con indicatore del segnale per trovare il punto migliore per aumentare la copertura della rete. Copertura Wi-Fi ottimale senza spazio per i dubbi.

Sicurezza One-Touch
Si collega in modo sicuro premendo un pulsante.

Porta Ethernet
Collega un dispositivo cablato o crea uno hot-spot wireless.

Specifiche tecniche
Wireless standard Wireless N
Wireless speed 300 Mbps 2.4 GHz
Antenna type 2 fixed omni-directional antennas
Wired interface 1 x Fast Ethernet LAN
Wireless modes Wireless client, Wireless extender


Documentazione
Scheda tecnica
Guida installazione
Manuale utente

Firmware
DAP-1325 A1 1.08B01 EU multi 20220926 | Changelog
DAP-1325 A1 1.07 build 01 20200717 note di versione incluse
DAP-1325 A1 1.03 build 01 20180515 con nota edizione cumulativa ed istruzioni per la transizione
DAP-1325 A1 1.02 build 04 20180411 con nota edizione cumulativa | Necessario per aggiornare alla v1.03
DAP-1325 A1 1.02 build 01 20171026
DAP-1325 A1 1.01 build 02 20170516 con nota edizione cumulativa
DAP-1325 A1 1.00 build 05 20170113 con nota edizione

N.B. Le versioni 1.02 & 1.03 non permettono rispettivamente retrocessioni, cioè aggiornamento alla versione precedente né a tutte le altre antecedenti!

Supporto internazionale D-Link
Pagina prodotto: Italia, Sud Africa, Mongolia
Sito FTP: Europa, Germania, Canada, Russia
Supporto Tecnico: TW TSD, Singapore, Canada

m4ss1

#1
Approfondimenti
Interfaccia seriale DAP-1325 A1

Pagine nascoste
dlinkap[ultime 4 cifre dell'indirizzo mac].local/version.txt
Citazione di: D-Link MNHardware
Processor
MT7628NN (580MHz)

RAM
• 64MB, DDR2 SDRAM

Flash
• 8MB, SPI

Interfaces
• 10/100BASE-TX LAN port

LEDs
• POWER/WPS
• Wi-Fi Signal Strength

Buttons
• WPS button to set up wireless connection
• RESET button to restore factory default settings

Antenna
• Two external non-detachable antennas (2 dBi)

MIMO
• 2 x 2

Power connector
• CEE 7/16 plug for AC power supply

Nuove funzionalità aggiunte
A partire dalla versione firmware 1.06 viene aggiunto il supporto agli standard 802.11k & 802.11v[1] per la funzione smart mesh roaming[2].
802.11k: consente alle informazioni di essere ritrovate in modo che il dispositivo possa scegliere l'AP migliore a cui connettersi.
802.11v: consente ai dispositivi di scambiarsi informazioni sulla topologia di rete, l'ambiente RF / le interferenze (rendendosi consapevoli della rete)[3].

How do I enable Smart Mesh Roaming on my range extender?

[4]

DAP-1325 A1 1.06 build 06 20191220 con nota edizione cumulativa ed istruzioni per la transizione | Altra nota edizione cumulativa

N.B. La versione 1.06 non permette retrocessioni, cioè aggiornamenti alla versione precedente né a tutte le altre antecedenti!

Documentazione multimediale
Immagini
FCC ID

Foto interne DAP-1325 A1
Effettuare l'accesso al forum per visualizzare gli allegati.
Non puoi visualizzare questo allegato.
Non puoi visualizzare questo allegato.

Video
Cerca con Google

Firmware altro
MT7628_3.0.1_2019.03.15-12.33 | Внесенные изменения

Datasheet
Installation Guide
User Manual

Pestomarco

Ciao a tutti, scrivo perchè avrei due problemi (non so se collegati).
Ho appena acquistato il DAP-1325 Range Extender Wi‑Fi N300 (https://eu.dlink.com/it/it/products/dap-1325-n300-wifi-range-extender) perchè ho bisogno di estendere il segnale del wifi al piano di sopra (casa di due piani...circa 80 metri quadri per piano).

ho una 50 mega ma dopo la configurazione dell'extender il pc al piano di sopra, collegato alla rete tramite wifi, arriva a un massimo di 10 mega.

ho già preso tutte le accortezze del caso come ad esempio collegamento diretto alla presa (non uso ciabatte) e ho posizionato l'extender appena finite le scale...di fatto il router e l'extender distano in linea d'aria pochi metri e non hanno muri in mezzo.

volevo quindi sapere se è una condizione normale passare da una 50 mega a una 10 o se probabilmente sto sbagliando qualcosa io.

p.s. un secondo problema (non so se collegato) è che da quando ho installato l'extender non riesco più ad usare PureVPN...qui di seguito le caratteristiche tecniche se possono servire per capire se il non funzionamento sia legato all'extender o no: https://www.connessionivpn.it/recensioni/purevpn/

Grazie in anticipo per le risposte ;D

.fega.

Ciao, controlla nel router a quanto si connette il DAP e il livello di segnale.
Considera che questo è un ripetitore "classico" quindi se lo usi senza il cavo di rete la velocità wireless sarà dimezzata, dovresti quindi avere 150 Mbps teorici.
La differenza di velocità, da 50 a 10 mega, è eccessiva prova a spostarlo.
Qual'è la versione del firmware?

Pestomarco

Citazione di: .fega. il 10 Agosto 2019, 12:01:17Ciao, controlla nel router a quanto si connette il DAP e il livello di segnale.
Considera che questo è un ripetitore "classico" quindi se lo usi senza il cavo di rete la velocità wireless sarà dimezzata, dovresti quindi avere 150 Mbps teorici.
La differenza di velocità, da 50 a 10 mega, è eccessiva prova a spostarlo.
Qual'è la versione del firmware?

Ciao fega, grazie per la risposta. oggi la connessione va molto più veloce. circa 30 mega. onestamente non so cosa sia successo. sono stato fuori casa due giorni per il weekend e al mio ritorno il segnale è migliorato. forse era un problema momentaneo...non so...

Simone Esse

Salve a tutti
Ho acquistato l'extender Wi-Fi Dap 1325 poiché il segnale al piano inferiore nella mia abitazione arriva debole. Considerando che la mia rete internet non è buona non è stabile (ho reclamato più e più volte) nelle condizioni migliori viaggio dai 20 ai 25.
Ho provato in primis la configurazione rapida premendo il tasto wps sul router e sull'extender ma con esito negativo. I valori allo speed test sono quasi a 0.
Successivamente ho scaricato l'app Qrs Mobile tramite iPhone 6s. Ho seguito le istruzioni alla lettera. Dopo aver selezionato la rete Wi-Fi creata (Ext)
anche qui non riesco a navigare, i valori di segnale sono sempre a 0.
Mi è stato detto di provare a fare la configurazione tramite pc fisso ma la connessione internet con questo è tramite cavo poiché non ho la ricezione wireless su di esso.
Avete consigli??
Grazie mille

m4ss1

Ciao Simone, devi cercare un punto dove il segnale wireless del router è discreto altrimenti la velocità sarà bassa.
Verifica che la versione del firmware installato sia la 1.03B01 EU 20180821 e, se necessario, aggiorna usando il firmware intermedio 1.02 EU 20181001.

Trovi tutto nel primo messaggio della discussione.

Pondera

Nota edizione DE cumulativa firmware DAP-1325 A1 1.06 build 06 20191220.

DAP-1325 Rev.A Firmware Release Notes


Firmware: FW 1.06b06
Hardware: Rev. Ax
Data: 2019/12/20

Problems Resolved:
1. Stricter device password(admin password) requirement in GUI.
2. Support 802.11k/v.

----------

Firmware: FW 1.03b01
Hardware: Rev. Ax
Data: 2018/05/15

Problems Resolved:
1. Fixes security issue.

----------

Firmware: FW 1.02b04
Hardware: Rev. Ax
Data: 2018/04/11

Problems Resolved:
1. Fix Extender stops working after a while.

----------

Firmware: FW 1.02b01
Hardware: Rev. Ax
Data: 2017/10/26

Problems Resolved:
1. Fix WPA2 KRACK issue.

----------

Firmware: FW 1.01b02
Hardware: Rev. Ax
Data: 2017/05/16

Problems Resolved:
1. Fix extender can't assosiate with the root router, when router changes WLAN channel.
2. Fix device sometime can't get IP from root router.

----------

Firmware: FW 1.00b05
Hardware: Rev. Ax
Data: 2017/01/13

Notes:
1st Release.



Estratto dall'altra nota edizione cumulativa TW TSD e traduzione automatica CHI-ENG

Project Name: DAP-1325
HW version: A1

Firmware version: v1.03B01
Date: Tuesday, May 15, 2018, 18:56:32
MD5: C04D0F82ED67EB149287342DDF7519C7
SHA1: 4FB4ADA79B44AA39EC82D64575417E012588732A
CRC32: E6CD38EA

Problems Resolved:
1. FW bin file import encryption
Enhancements:
1. N/A.

Pondera

Per il momento lasciamo la v1.06 nel 2° messaggio.
Dalla 1.03 non si torna indietro. E nemmeno dalla 1.06. C'è però la possibilità di retrocedere alla 1.03 firmandola come una 1.06 e, volendo, riaggiornando alla 1.03 originale.

Nella 1.06, subito dopo il reset, compare la finestra del wizard mancante dell'icona [X] per CHIUDI nell'angolo in alto a destra e quindi non la si può togliere senza aver concluso la procedura.



Ma è possibile richiamare qualsiasi altra voce dei menu conoscendone l'indirizzo.

http://dlinkap.local/Home.html [WIZARD]

http://192.168.0.50/Login.html

http://192.168.0.50/Extender.html
http://192.168.0.50/Network.html

http://192.168.0.50/Admin.html
http://192.168.0.50/System.html
http://192.168.0.50/Upgrade.html
http://192.168.0.50/Statistics.html

http://shareport.local/

m4ss1

Pubblicate nel secondo messaggio le foto interne del DAP-1325 A1.

m4ss1

#10
Interfaccia seriale DAP-1325 HW A1
Effettuare l'accesso al forum per visualizzare gli allegati.
Non puoi visualizzare questo allegato.
Velocità: 57600, Data bits:8, Stop bits:1, Parity:none, Flow control:none

Log di avvio DAP-1325
[04060C0E][04060C0B]
DDR Calibration DQS reg = 0000888A


U-Boot 1.1.3 (Dec  2 2016 - 21:11:16)

Board: Ralink APSoC DRAM:  64 MB
relocate_code Pointer at: 83fb0000
flash manufacture id: ef, device id 40 17
find flash: W25Q64BV
*** Warning - bad CRC, using default environment

============================================
Ralink UBoot Version: 4.3.0.0
--------------------------------------------
ASIC 7628_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Dec  2 2016  Time:21:11:16
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

 ##### The CPU freq = 580 MHZ ####
 estimate memory size =64 Mbytes
RESET MT7628 PHY!!!!!!
Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.
   k: Load system code then write to Flash via Web.

You choosed 3
                                                                              0

3: System Boot system code via Flash.
## Booting image at bc050000 ...
   Image Name:   Linux Kernel Image
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    5625199 Bytes =  5.4 MB
   Load Address: 80000000
   Entry Point:  8000c150
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8000c150) ...
## Giving linux memsize in MB, 64

Starting kernel ...


LINUX started...

 THIS IS ASIC
Linux version 2.6.36 (root@mtn) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #17 Tue May 15 11:43:28 CST 2018

 The CPU feqenuce set to 575 MHz

 MIPS CPU sleep mode enabled.
CPU revision is: 00019655 (MIPS 24Kc)
Software DMA cache coherency
Determined physical RAM map:
 memory: 04000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: console=ttyS1,57600n8 root=/dev/ram0 console=
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, , 4-waylinesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=0005930f
Readback ErrCtl register=0005930f
Memory: 56404k/65536k available (3287k kernel code, 9084k reserved, 760k data, 4240k init, 0k highmem)
NR_IRQS:128
console [ttyS1] enabled
Calibrating delay loop... 386.04 BogoMIPS (lpj=772096)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
Switching to clocksource Ralink Systick timer
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
msgmni has been set to 110
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered (default)
Ralink gpio driver initialized
i2cdrv_major = 218
Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
serial8250: ttyS0 at MMIO 0x10000d00 (irq = 21) is a 16550A
serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A
brd: module loaded
flash manufacture id: ef, device id 40 17
W25Q64BV(ef 40170000) (8192 Kbytes)
mtd .name = raspi, .size = 0x00800000 (8M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 5 MTD partitions on "raspi":
0x000000000000-0x000000800000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000001000000 : "Kernel"
mtd: partition "Kernel" extends beyond the end of device "raspi" -- size truncated to 0x7b0000
rdm_major = 253
GMAC1_MAC_ADRH -- : 0x0000409b
GMAC1_MAC_ADRL -- : 0xcd6062fa
Ralink APSoC Ethernet Driver Initilization. v3.1  256 rx/tx descriptors allocated, mtu = 1500!
GMAC1_MAC_ADRH -- : 0x0000409b
GMAC1_MAC_ADRL -- : 0xcd6062fa
PROC INIT OK!
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPTP driver version 0.8.5
IMQ driver loaded successfully.
        Hooking IMQ after NAT on PREROUTING.
        Hooking IMQ before NAT on POSTROUTING.


=== pAd = c014d000, size = 1408928 ===

<-- RTMPAllocTxRxRingMemory, Status=0, ErrorValue=0x
<-- RTMPAllocAdapterBlock, Status=0
RtmpChipOpsHook(492): Not support for HIF_MT yet!
mt7628_init()-->
mt7628_init(FW(8a00), HW(8a01), CHIPID(7628))
e2.bin mt7628_init(1135)::(2), pChipCap->fw_len(63888)
mt_bcn_buf_init(218): Not support for HIF_MT yet!
<--mt7628_init()
u32 classifier
    Performance counters on
nf_conntrack version 0.5.0 (881 buckets, 3524 max)
IPVS: Registered protocols ()
IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
IPVS: ipvs loaded.
GRE over IPv4 demultiplexor driver
gre: can't add protocol
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
TCP cubic registered
NET: Registered protocol family 10
NET: Registered protocol family 17
Bridge firewalling registered
Ebtables v2.0 registered
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
Warning: unable to open an initial console.
status_socket_nl_create
kernel_init:Netlink socket create ok!
Freeing unused kernel memory: 4240k freed
Algorithmics/MIPS FPU Emulator v1.5
Welcome to
     __   ___  _____  _____   _  _______ ______  _____  _   ___
    |  \ /   ||  ___||  __ \ | ||  __  ||__  __||  ___|| | /  /
    |   ^    || |__  | |  \ \| || |  | |  | |   | |__  | |/  /
    |  | |   ||  ___|| |  | || || |__| |  | |   |  ___||    \
    |  | |   || |___ | |__/ /| ||  __  |  | |   | |___ | |\  \
    |__| |___||_____||_____/ |_||_|  |_|  |_|   |_____||_| \__\

                        = Everyday Genius =

led=11, on=1, off=4000, blinks,=1, reset=1, time=4000
led=37, on=4000, off=1, blinks,=1, reset=1, time=4000
TX_BCN DESC a2b7c000 size = 320
RX[0] DESC a2b7f000 size = 1024
RX[1] DESC a2b80000 size = 1024
E2pAccessMode=0
cfg_mode=9
cfg_mode=9
wmode_band_equal(): Band Equal!
AndesSendCmdMsg: Could not send in band command due to diable fRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD
APSDCapable[0]=0
APSDCapable[1]=0
APSDCapable[2]=0
APSDCapable[3]=0
APSDCapable[4]=0
APSDCapable[5]=0
APSDCapable[6]=0
APSDCapable[7]=0
APSDCapable[8]=0
APSDCapable[9]=0
APSDCapable[10]=0
APSDCapable[11]=0
APSDCapable[12]=0
APSDCapable[13]=0
APSDCapable[14]=0
APSDCapable[15]=0
default ApCliAPSDCapable[0]=0
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
load fw image from fw_header_image
AndesMTLoadFwMethod1(2182)::pChipCap->fw_len(63888)
FW Version:20151201
FW Build Date:20151201183641
CmdAddressLenReq:(ret = 0)
CmdFwStartReq: override = 1, address = 1048576
CmdStartDLRsp: WiFI FW Download Success
MtAsicDMASchedulerInit(): DMA Scheduler Mode=0(LMAC)
efuse_probe: efuse = 10000012
RtmpChipOpsEepromHook::e2p_type=0, inf_Type=4
RtmpEepromGetDefault::e2p_dafault=2
RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 2
NVM is FLASH mode
1. Phy Mode = 14
Country Region from e2p = 1ff
tssi_1_target_pwr_g_band = 28
2. Phy Mode = 14
3. Phy Mode = 14
NICInitPwrPinCfg(11): Not support for HIF_MT yet!
NICInitializeAsic(651): Not support rtmp_mac_sys_reset () for HIF_MT yet!
mt_mac_init()-->
MtAsicInitMac()-->
mt7628_init_mac_cr()-->
MtAsicSetMacMaxLen(1276): Set the Max RxPktLen=1024!
<--mt_mac_init()
        WTBL Segment 1 info:
                MemBaseAddr/FID:0x28000/0
                EntrySize/Cnt:32/128
        WTBL Segment 2 info:
                MemBaseAddr/FID:0x40000/0
                EntrySize/Cnt:64/128
        WTBL Segment 3 info:
                MemBaseAddr/FID:0x42000/64
                EntrySize/Cnt:64/128
        WTBL Segment 4 info:
                MemBaseAddr/FID:0x44000/128
                EntrySize/Cnt:32/128
AntCfgInit(2940): Not support for HIF_MT yet!
MCS Set = ff ff 00 00 01
MtAsicSetChBusyStat(861): Not support for HIF_MT yet!
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
CmdSlotTimeSet:(ret = 0)
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
----------------------------send status to monitor = 0
-----------------pid:0-------------
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
MtAsicSetRalinkBurstMode(3047): Not support for HIF_MT yet!
MtAsicSetPiggyBack(796): Not support for HIF_MT yet!
reload DPD from flash , 0x9F = [c200] doReload bit7[0]
CmdLoadDPDDataFromFlash: Channel = 6, DoReload = 0
MtAsicSetTxPreamble(3026): Not support for HIF_MT yet!
MtAsicAddSharedKeyEntry(1343): Not support for HIF_MT yet!
The 2-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 2
MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0
Main bssid = 40:9b:cd:60:62:fb
<==== rt28xx_init, Status=0
@@@ ed_monitor_exit : ===>
@@@ ed_monitor_exit : <===
mt7628_set_ed_cca: TURN OFF EDCCA  mac 0x10618 = 0xd7083f0f, EDCCA_Status=0
WiFi Startup Cost (ra0): 4.316s
------------------------------------------kernel monitor id=566
Raeth v3.1 (Tasklet,SkbRecycle)

phy_tx_ring = 0x005ef000, tx_ring = 0xa05ef000

phy_rx_ring0 = 0x005f0000, rx_ring0 = 0xa05f0000
GMAC1_MAC_ADRH -- : 0x0000409b
GMAC1_MAC_ADRL -- : 0xcd6062fa
RT305x_ESW: Link Status Changed
device eth2 entered promiscuous mode
device ra0 entered promiscuous mode
AddTxSType: already registered TxSType (PID = 32, Format = 0
The 2-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 2
br0: port 1(ra0) entering learning state
br0: port 1(ra0) entering learning state
br0: port 1(ra0) entering forwarding state
restart mdns...
Ralink APSoC Hardware Watchdog Timer
Started WatchDog Timer.
led=13, on=4000, off=1, blinks,=1, reset=1, time=4000
Jan  1 00:00:22 mDNSProxyResponderPosix: mDNSCoreReceiveResponse: Received from 192.168.0.50:5353   15 50.0.168.192.in-                                                 addr.arpa. PTR dlinkap.local.
Jan  1 00:00:22 mDNSProxyResponderPosix: mDNSCoreReceiveResponse: Unexpected conflict discarding   19 50.0.168.192.in-a                                                 ddr.arpa. PTR dlinkap62FA.local.
Jan  1 00:00:22 mDNSProxyResponderPosix: mDNS_Deregister_internal: Record 7FDCA554 not found in list    4 dlinkap62FA.l                                                 ocal. Addr 192.168.0.50
Jan  1 00:00:22 mDNSProxyResponderPosix: mDNS_Deregister_internal: Record 7FDCA8C0 not found in list   19 50.0.168.192.                                                 in-addr.arpa. PTR dlinkap62FA.local.
reload DPD from flash , 0x9F = [c200] doReload bit7[0]
CmdLoadDPDDataFromFlash: Channel = 6, DoReload = 0
reload DPD from flash , 0x9F = [c200] doReload bit7[0]
CmdLoadDPDDataFromFlash: Channel = 6, DoReload = 0
Stopped WatchDog Timer.
Ralink APSoC Hardware Watchdog Timer
Started WatchDog Timer.
switch register base addr to system register 0xb0000000
write offset 0x60, value 0x55054450
write offset 0x654, value 0x6040
br0: port 1(ra0) entering forwarding state
br0: port 1(ra0) entering learning state
br0: port 1(ra0) entering learning state
reload DPD from flash , 0x9F = [c200] doReload bit7[0]
CmdLoadDPDDataFromFlash: Channel = 6, DoReload = 0
reload DPD from flash , 0x9F = [c200] doReload bit7[0]
CmdLoadDPDDataFromFlash: Channel = 6, DoReload = 0
br0: port 1(ra0) entering forwarding state
led=11, on=5, off=5, blinks,=4000, reset=1, time=4000
led=37, on=5, off=5, blinks,=4000, reset=1, time=4000
init: can't log to /dev/tty5
starting pid 9002, tty '/dev/ttyS1': '/bin/sh'


BusyBox v1.12.1 (2018-05-08 16:57:04 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

Premendo il tasto 2 durante l'avvio è possibile effettuare il downgrade del firmware tramite TFTP.

Ho testato anche il flash del firmware russo, tutto funziona perfettamente ma è necessario effettuare il reset dopo l'aggiornamento.

Ralink UBoot Version: 5.0.0.0
--------------------------------------------
ASIC 7628_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Feb 21 2017  Time:10:58:24
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

 ##### The CPU freq = 580 MHZ ####
 estimate memory size =64 Mbytes
RESET MT7628 PHY!!!!!!DRU DAP-1320

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.
default: 3

You choosed 2
                                                                                                                        0


2: System Load Linux Kernel then write to Flash via TFTP.
 Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
 Please Input new ones /or Ctrl-C to discard
        Input device IP (192.168.0.50) ==:10.10.10.123
        Input server IP (192.168.0.180) ==:10.10.10.3
        Input Linux Kernel filename () ==:test.bin

 NetTxPacket = 0x83FE5E00

 KSEG1ADDR(NetTxPacket) = 0xA3FE5E00

 ETH_STATE_ACTIVE!!
TFTP from server 10.10.10.3; our IP address is 10.10.10.123
Filename 'test.bin'.

 TIMEOUT_COUNT=10,Load address: 0x82000000

Got ARP REPLY, set server/gtwy eth addr (00:1f:16:ae:1d:24)
Got it
#################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #############
done
Bytes transferred = 5389206 (523b96 hex)
LoadAddr=82000000 NetBootFileXferSize= 00523b96
..................................................................................
..................................................................................
.
.
Done!


Pondera


ANTONIO TOLONE

Buongiorno a tutti. Ho comprato un Dap 1325 per estendere la rete wifi anche al piano inferiore. Dopo qualche tempo di buon funzionamento ho cambiato gestore telefonico. Quando ho provato a reinstallare (dopo aver  effettuato il ripristino alle informazioni di fabbrica) il led mi da lampeggiante giallo ma nel computer dove volevo effettuare la registrazione mi da una rete chiamata default a cui non riesco a connettermi senza la password che non corrisponde a quella che avevo  immesso la prima volta. In conclusione non riesco a far nulla. Chi mi può aiutare.
Grazie a chiunque avra' la pazienza di farlo.

m4ss1

Citazione di: ANTONIO TOLONE il 22 Marzo 2021, 11:25:55una rete chiamata default a cui non riesco a connettermi senza la password
:o
Ciao Antonio, qual è la versione hardware del DAP-1325? Controlla nell'etichetta.
Hai la possibilità di collegarlo al PC con un cavo di rete?

ANTONIO TOLONE

Citazione di: m4ss1 il 22 Marzo 2021, 22:11:14:o
Ciao Antonio, qual è la versione hardware del DAP-1325? Controlla nell'etichetta.
Hai la possibilità di collegarlo al PC con un cavo di rete?

Ciao grazie per la risposta. La  versione Hardware dovrebbe essere: H/W A1 F/W 1.06  e si ho la possibilità di collegarlo  al PC con il cavo di rete- Attendo con ansia indicazioni ;D . Grazie ancora

m4ss1

#15
Configura la scheda di rete LAN del PC con l'indirizzo IP statico 192.168.0.10
Collega il DAP alla PC con il cavo di rete e apri http://192.168.0.50
Nel primo messaggio della discussione troverai il collegamento per scaricare il firmware 1.07b01, aggiorna il DAP-1325 (usa il file 2_DAP-1325_RevA_Firmware_107b01.bin) e dopo aver completato la configurazione ripristina la configurazione della scheda di rete LAN (automatico).

m4ss1

Aggiornato primo messaggio: pubblicato il firmware DAP-1325 A1 1.07 build 01 20200717
DAP-1325 Rev.A Firmware Release Notes


Firmware: FW 1.07b01
Hardware: Rev. Ax
Data: 2020/07/17

Problems Resolved:
1. Fix WLAN connectivity issue.

----------

Firmware: FW 1.06b06
Hardware: Rev. Ax
Data: 2019/12/20

Problems Resolved:
1. Stricter device password(admin password) requirement in GUI.
2. Support 802.11k/v.

----------

Firmware: FW 1.03b01
Hardware: Rev. Ax
Data: 2018/05/15

Problems Resolved:
1. Fixes security issue.


Nick 55

Buongiorno a tutti. HELP! Ho acquistato il DAP-1325 collegato e con il WPS collegato al router con segnale ottimo. Apro l'elenco delle reti wi fi disponibili e non appare nella lista ( ne ho collegato un altro diverso e funziona perfettamente) se collego  il  pc con la presa LAN funziona ethernet ma WI FI non funziona. Nel tutorial appare immediatamente in elenco. Cosa devo fare per configurarlo?? Grazie anticipate

Sandri


messer1951

Salve a tutti come installo il nuovo firmware sul mio DAP-1325 ed in più non riesco a configurare sul mio router fibra della tim,forse devo attivare ipv6 ? Vi ringrazio della sicura risposta un saluto.

Licenza Creative Commons
Il contenuto dei messaggi del forum è distribuito con
Licenza Creative Commons Attribuzione Non commerciale 4.0
Tutti i marchi registrati citati appartengono ai legittimi proprietari