Valutazione discussione:
  • 1 voto(i) - 5 media
  • 1
  • 2
  • 3
  • 4
  • 5
DIR-826L: Wireless N 600 Dual Band Gigabit Cloud Router 2000
#21
Nessuno puo' aiutarmi ragazzi???

Che dite, mi conviene caricarli il firmware aggiornato oppure mi conviene chimare l'assistenza clienti e farmelo sostituire in garanzia???

grazie e buonadomenica a tutti
Cita messaggio
#22
Allora ragazzi....
Ho resettato il mio 826... ho inserito il firmware 1.03 (quello stabile)
Ho settato 2 reti.

In tutto quindi 3 reti:
1) La standard del router 2740 a 2.4
2) La 2.4 del 628
3) La 5ghz del 628

Problema che comunque non va via....
Le due reti STANDARD a 2.4ghz ovvero quella del router tradizionale e quella del 628 vanno benissimo

l'unica che non funziona e la VELOCE a 5ghz... che funziona per qualche minuto dopo di che si stacca.... e non va piu'! ! !

Cosa fare??? DILEMMA...

Assistenza ! ! ! ???
Cita messaggio
#23
Se hai il firmware 1.01 il primo consiglio è quello di aggiornare, dato che ne sono usciti 4 o 5 di correttivi. Con il firmware originario anch'io effettivamente avevo riscontrato dei problemi con la rete a 5 Ghz.
Installa l'ultimo disponibile, l'1.04B06 del maggio 2013 e verifica il funzionamento. Ti consiglio un reset pre aggiornamento e uno post aggiornamento (sempre dall'interfaccia web alle condizioni di factory default e non con il tastino posteriore) e una completa riconfigurazione a mano.
Verifica poi che i parametri avanzati della rete wireless (beacon interval, fragmentation packet etc... tra i vari router siano esattamente gli stessi).

Download: ftp.ftp.dlink.pl/dir/dir-826L/driver_software/DIR-826L_fw_revA_1-04B06_all_en_20130305.zip

PS: verifica anche che non ci siano impostazioni di scheduling attive per la rete a 5 Ghz che la disattivino a seconda dell'orario e che la scheda Time e Date del router sia configurata per prendere l'ora corretta.
Cita messaggio
#24
ciao e grazie per la risposta...
Cosa intendi per beacon interval???

Posso avere tutte e tre le reti accese???
o mi conviene disattivarne una?
Grazie ! ! !

Su la tradizionale a 2.4ghz quella che esce dal router 2740b ho collegato 8 ip cam esterne...

cosa mi consigli?

Grazie
Cita messaggio
#25
In teoria puoi tenere tutte e tre le reti accese sul 826l però tieni presente che in realtà la 2.4 Ghz ha banda condivisa su due SSID e sempre 300 Mbit sono.
La 5 Ghz aggiunge ulteriori 300 Mbit, ma la portata di queste reti è quasi la metà della 2.4 Ghz come copertura.
Cita messaggio
#26
quindi mi conviene tenere accesa solo una linea 2.4 ... lascio accesa quella del router adsl originale???
infatti ho notato che la copertura a 5 ghz e' veramente irrisoria rispetto alla 2.4 ghz...
Cita messaggio
#27
speriamo che caricando questo firmware che hai postato possa risolvere il problema ! ! !

Ma nell'eventualità posso mandarlo in garanzia con questo firmware???

Fanno storie?

Grazie
Cita messaggio
#28
No, il firmware è ufficiale di D-Link international. Comunque lo puoi mandare in assistenza tramite il negoziante (conviene sempre nei 2 anni) che di solito te ne dà subito un altro al volo ed in ogni caso puoi rimettergli il vecchio firmware.
Cita messaggio
#29
comunque... non funge anche con il nuovo firmware. 1.04.. nulla.... e' rotto ! ! !

Peccato per 2 settimana e' andato una scheggia.... ma poi e' morto!!!

Sapete come fare per farmelo sostituire???

Bisogna chiamare un numero verde qualcosa???

Aiutatemi grazie ! ! !
Cita messaggio
#30
Devi contattare il negoziante. Pensa a tutto lui.
Cita messaggio
#31
Ciao... allora ho contattato l'assistenza clienti DLINK ! ! !
davvero preparati nulla da dire...

mi hanno detto di cambiare la banda della 5ghz
e di cambiare la chiave da WEP a WPA....

sembra vada bene... un po' lentino ma va bene...
Cita messaggio
#32
Beh, sì, ovviamente il 5 Ghz non funziona con crittografia WEP ...
Cita messaggio
#33
Nuovo firmare per DIR-826L v. 1.04B07 beta 02 con file della lingua italiana aggiunto nel primo post.
Miglioramenti:

Codice:
Firmware Release Note
Project Name: DIR-826L
HW version: A1
Region/OEM code: WW
WLAN Domain: 0x10/US/NA
WLAN Driver:
Date: Nov. 28 2011
Channel List:
     2.4GHz: 1,2,3,4,5,6,7,8,9,10,11
       5GHz: 36,40,44,48,149,153,157,161,165
Flash size:16MB
DRAM size:128MB

===========================================================================================================================================
Date:2013-06-10
Firmware Version:v1.04B07beta02
Kernel: Linux version 2.6.36
Source version: 282
Check Sum: 0x61C80774

Note

For D-Track-HQ20130507000008
1.The mail size does not fill up 16K, it was only 14K approximately, it means that device sent email, but log did not on full.
2.The schedule rule "Always" in E-Mail notification page, DIR-826L will sending log mail every minutes (00:00:00~00:59:59).
The "Always" default setting should send log only 1 time in 00:00:00.

===========================================================================================================================================
Date:2013-06-04
Firmware Version:v1.04B07beta01
Kernel: Linux version 2.6.36
Source version:  248
Check Sum: 0x603B04FE

Note
1. Fixed D-Track-HQ20130517000001-DIR-826L_A1_v1.04b06beta01-DLNA

===========================================================================================================================================
Date:2013-05-10
Firmware Version:v1.04B07
Kernel: Linux version 2.6.36
Source version: 39
Check Sum: 0xCFEBD582

Note
1. Support Dlink IPv6 SPEC 2.06
2. Support D-Link AP and Router Specification for Timezone v1.00
3. Support D-Link Router Web-based Setup Wizard Specification with mydlink Service v1.05R

fix bugs:
pre-test

TSD
0023453: SharePort App - Video section issue
0023120: Network Settings
0017096: Lack information in syslog and log issue
0022655: WPS and guest zone issue
===========================================================================================================================================
Date:2013-04-11
Firmware Version:v1.04B06
Kernel: Linux version 2.6.36
Source version: 5133
Check Sum: 0xDC3CF62B

Note
1. Fix ncc crash (sp did not check whether the object is null in host filter section).
2. Fix LibUPnP security issue.
3. Fix NCC memory leak issue
4. Fix Security Vulnerability(shell command injection)
5. Disable DHCP always broadcast option
6. Change Reset button behavior back (follow spec)

fix bugs:
pre-test

TSD
issue on DIR-820L 0021932: Language pack upload issue
Web-gui will display incomplete after upload firmware file to language pack upload.
0022235: The "Virtual server" page will show incompletely when using IE and Firefox in CN/TW/JP.
0022236: The "Virtual server" page will show incompletely when using IE and Firefox in CN/TW/JP.
0022512: Router security issue
When WAN is connected and enter `reboot` into NTP server name field, DUT will reboot continuously. (need unplug the wan port)
===========================================================================================================================================
Date:2013-03-22
Firmware Version:v1.04B05
Kernel: Linux version 2.6.36
Source version: 5011
Check Sum: 0xB5B3F371

Note:
1. avoid Qos impact WAN connection.

Pre-test:
188 GUI pop ipv6 address illegal message when user select 6rd wan mode (with dhcpv4 option) and try to save

TSD:
0021443: Mydlink remote management port setting can not detect conflict with other function port issue
0021633: Chklst.txt issue
0021628: Access Control Add Port Filter Rules issue

===========================================================================================================================================
Date:2013-03-19
Firmware Version:v1.04B04
Kernel: Linux version 2.6.36
Source version: 4962
Check Sum: 0x09534AF8

Note:

Pre-test:
184 s/w reset DUT to default, broswer (EX: IE9/IE10) can't back to wizard page
188 GUI pop ipv6 address illegal message when user select 6rd wan mode (with dhcpv4 option) and try to save
189
1.push  ipv6 internet wizard , on step 1,2 right side frame has no frame line  ,see attaced photo
2.in manual mode step1  right side frame  has no frame line,see attaced photo    
190 in configure ipv6 internet step1 (ipv6 internet wizard) ,when user select pppoe mode share with pppv4 ,GUI can't store it ,pop wrong message (DUT had set pppv4)

TSD:
0021309: Check Online Firmware issue
DUT WAN not sent DNS query packet and web-gui will display incomplete for a period time, when change WAN Type: DHCP (Not get ip) to static ip, then "Check Now" Online Firmware.
0021301: Check Online Firmware issue
DUT WAN not sent DNS query packet and web-gui will display incomplete for a period time, when change WAN Type: DHCP (Not get ip) to static ip, then "Check Now" Online Firmware.
0021352: DHCP flag issue
DHCP flag in DHCP discover is different in Out-off-Box state and Internet Connection Setup Wizard.
0021300: Firmware check issue
DUT cannot query static DNS address when click firmware "Check Now" button.
0021304: Firmware check issue
DUT cannot query static DNS address when click firmware "Check Now" button.


===========================================================================================================================================
Date:2013-03-06
Firmware Version:v1.04B03
Kernel: Linux version 2.6.36
Source version: 4822
Check Sum: 0x91C516C1

Note:

pre-test
0020649: SharePort web access storage path issue. <-- Fail
¡@1. Login shareport web access and will see error triangle with Win7 + IE8 .
¡@2. Folder name field is not obvious with Win7 + IE8 .
¡@3. Upload file page is word wrap.

===========================================================================================================================================
Date:2013-03-04
Firmware Version:v1.04B02
Kernel: Linux version 2.6.36
Source version: 4788
Check Sum: 0x3FBDADFE

Note:
1. fix D-Track-HQ20130218000023: when DUT connect to 100M full (force) port, the throughput is lowest (negotiation issue).

Fixed bugs
TSD
0020106: Advanced - Network (WAN port speed negogiation issue)
0017882: IPv6 Status information issue
0019542: IPv6 - 6in4 issue
0019532: IPv6 - 6rd issue
0016039: Product Page URL issue
0020328: Can not detect USB 1.0 storage issue
0019518: IPv6 - 6rd issue
0020313: NetBIOS can only get one storage device issue
0019487: IPv6 PPPoE issue
0020305: SharePort web access storage path issue
0020242: "Always Broadcast" should be disabled by default issue
0018500: Configure settings can be loaded to other model issue
0019482: Storage wizard
0018746: Wireless status information issue
0019267: Web-based setup wizard not translated issue
0019377: Access Control policy naming issue
0019243: Attach special characters naming folder will cause Storage GUI error issue
0019668: Guest zone should not displayed in WPS manual page issue
0015114: Schedule rule list time format issue

===========================================================================================================================================
Date:2013-02-19
Firmware Version:v1.04B01
Kernel: Linux version 2.6.36
Source version: 4702
Check Sum: 0x6990B3AD

Note:
1. Firmware rename.

===========================================================================================================================================
Date:2013-02-08
Firmware Version:v1.03B04
Kernel: Linux version 2.6.36
Source version: 4691
Check Sum: 0x6C70252D

Note:

fix bugs:
pre-test
1. Auto detection (6RD): The valid lifetime and preferred lifetime not need count down when IPv6 WAN connection mode at 6RD mode.

===========================================================================================================================================
Date:2013-02-04
Firmware Version:v1.03B03
Kernel: Linux version 2.6.36
Source version: 4640
Check Sum: 0x683C4984

Note:
1. When IPv6 type set to 6rd, DUT will announce 1460 as MTU to LAN PC. It should be 1480 as in the same network environment, change IPv6 type to Autodetection, MTU announced to LAN PC is 1480.
2. UPNP icon disappear issue.
3. Fixed UPnP bug: multiple buffer overflow vulnerabilities (update the upnp version)

===========================================================================================================================================
Date:2012-12-17
Firmware Version:v1.03B02
Kernel: Linux version 2.6.36
Source version: 4164
Check Sum: 0xD01C9303

Note
1. add WPS 2.0 behavior in guestzone
2. fix IPv6 information is missing in mdns.
3. fix shareport.local cannot be found on Android platform (Shareport Mobile).
4. fix WSCD 100% CPU usage issue.
5. Fixed wrong lease time from DHCP server that maybe was having hard time to get IP.

fix bugs:
pre-test
1.Fixed Terms Of Use link should direct with current lang chosen
2.Fixed Setup Wizard wireless setting should be saved after user press cancel button

TSD
0018244: Virtual Server - Wake On Lan
0018694: IPv6 mDNS issue
===========================================================================================================================================
Date:2012-11-23
Firmware Version:v1.03B01
Kernel: Linux version 2.6.36
Source version: 3980
Check Sum: 0x42296504

Note
1. Add DLNA ver. 1.0.25
2. Update Boot Loader DIR826LA1_BOOT100B15_128M.bin
¡@ (Restore to default when upgrade firmware from backup mode.)
3. Support new SSID rule for 5G WIFI.
4. DRWS is now following SPEC(1.0.7) and modify UploadFile( using timestamp )
5. Setup Wizard follows spec v1.03
6. Shareport using paging loading (50 items per page)
7. Open shareport.local
8. Improve category cache.
9. Fixed Advanced-IPv6 Firewall&IPv6 Routing can show other language in WPS webpage

fix bugs:
pre-test
1. DUT have send out DHCPv6 information message to get DNS address but the DNS address at IPv6 status page is get from RA, not from DHCP server

TSD
0018241: WiFi Protected Setup.
0018270: WPS PIN issue.Set both bands SSID to 32 words cause Web Error, but Chinese characters no fixed.
0018244: Virtual Server - Wake On Lan
0017390: IPv6 PPPoE on demand issue
0016378: Log issue

===========================================================================================================================================
Date:2012-11-09
Firmware Version:v1.02B28
Kernel: Linux version 2.6.36
Source version: 3893
Check Sum: 0xED18576F

Note
1. changed back the hardware buttons to 5 second timeout, same as previous behavior.

fix bugs:
pre-test
1. DUT will be send out RS message when IPv6 select ¡§pppoe share with IPv4¡¨ to set. (base on  TSD bug 0017901)
2. Before press connect  button (TSD 0017900 test step2)  DUT will be dial-up pppoe. (base on  TSD bug 0017901)

TSD
0017945: Autoconfiguration DNS issue
0017920: IPv6 PPPoE on demand reconnect issue

===========================================================================================================================================
Date:2012-11-05
Firmware Version:v1.02B27
Kernel: Linux version 2.6.36
Source version: 3849
Check Sum: 0x79792FDA

Note:

fix bugs:
TSD
0016960: BT endurance test
0017135: DMZ
0017811: BT Endurance Stress Test
0017815: GUI in Windows 8 issue
0017637: WAN PING GUI issue
0017641: WPS GUI issue
0017766: SharePort Mobile Web Access page issue
0017759: Clear DNS field issue
0017844: SharePort Web Access issue
0017900: IPv6 PPPoE issue

===========================================================================================================================================
Date:2012-10-22
Firmware Version:v1.02B26
Kernel: Linux version 2.6.36
Source version: 3777
Check Sum: 0x650837F8

Note:
Fixed Configuration can not loaded issue

===========================================================================================================================================
Date:2012-10-18
Firmware Version:v1.02B25
Kernel: Linux version 2.6.36
Source version: 3778
Check Sum: 0x8B86C463

Note:
1. Wireless driver patch (RTS/CTS)

fix bugs:
Pretest
1. fix 5G band is disable at default value.

TSD
0017381    When disable WPS,all buttons are not gray.(User can generate PIN or reset PIN)
0016882    1.add user in shareport
                2.change access path of user
                issue: Browse folders in "Append New Folder" window by IE9, after expand folders, on the top of the folder window will be blank. Not happened in other browsers.
0017397    SharePort Web Access cannot display all folder name if folder name is !@#$%^&*().
0017193    If "NetBIOS Scope" field contain space character,the name will show incompletely in Wireshark packet.
0016327    1.Restore DUT factory default
                2.Enable remote management
                3.Log in DDNS and register DUT WAN IP in web page (not log in DDNS by DUT).
                issue: Can not remote manage DUT by using web login DDNS.
0017428    When Upload or Delete file via Share port remote access and replug USB,the USB device name will be changed to other name(ex. usb_A1 to usb_B1).The user Access path will fail,user will Permission denied from Remote Access.
0017459    Open web page or ping domain name (i.e.: www.google.com) can not trigger PPPoE connection. Only ping IP address out side WAN(i.e.: 168.95.1.1) can trigger.

===========================================================================================================================================
Date:2012-10-12
Firmware Version:v1.02B24
Kernel: Linux version 2.6.36
Source version: 3722
Check Sum: 0x8DBE0002

Note:
1. fix ´¡¤JUSB¡AµM«á¶i¤Japp«á²¾°£¾÷¾¹¤WªºUSB¡A¦¹®É¶i¤JFolder,·|Åã¥Ü¡¨Empty¡¨ (USB¬O¦³Àɮתº)¦Ó¶i¤JMusic, Movie and Photo DIR-626L·|Åã¥Ü¡¨Can¡¦t connect to target router, please make sure the device that you connected and IP address is correct¡¨.
2. DUT downgrade FW and will cause DUT can not reboot.

fix bugs:
TSD
0017310    When disable WPS,all buttons are not gray.(User can generate PIN or reset PIN).
0017288    The Web Access Logging in ACCESS CONTROL function can't be disabled.(Save setting but still enabled)
0017290    The access control device name always display "undefined".


===========================================================================================================================================
Date:2012-10-05
Firmware Version:v1.02B23
Kernel: Linux version 2.6.36
Source version: 3688
Check Sum: 0x6519598B

1. NTP sync interval => 7 days
2. Please test IPv6 throughput (WAN<=>LAN, WLAN<=>WAN)
3.    fix 1.    [DIR-626L] ·í§Ú¶i¤JFolder«á¦b¡AµLªk¥Îªð¦^Áä¦^¨ì­º­¶¡C
                2.    [DIR-626L] ´¡¤JUSB¡AµM«á¶i¤Japp«á²¾°£¾÷¾¹¤WªºUSB¡A¦¹®É¶i¤JFolder,·|Åã¥Ü¡¨Empty¡¨ (USB¬O¦³Àɮתº)¦Ó¶i¤JMusic, Movie and Photo DIR-626L·|Åã¥Ü¡¨Can¡¦t connect to target router, please make sure the device that you connected and IP address is correct¡¨.

fix bugs:
pre-test
1. DUT can not ready after DUT downgrade the firmware.

TSD
17125    "1.SharePort Mobile can not browse file, music and video in Android system, it always pop up ""can not connect to device"" error message.
            2.SharePort Mobile can not browse document in IOS system, it always pop up ""permission deny"" error message."
17084    Click "Check now" in Check Online Now for Latest Firmware and Language pack Version, GUI display nothing after Firmware update checks if there is no newer version.
16992    After set wireless security from WPA-TKIP-EAP to none security, WPS function cannot be enable.
17005    After DDNS settings saved, DDNS setting page always pop up abandon setting message when leaving the page.
16228    Access Shareport Mobile remote page with no device, page will display error.
16000    During BT test, DUT always reboot in random time.

===========================================================================================================================================
Date:2012-09-28
Firmware Version:v1.02B22
Kernel: Linux version 2.6.36
Source version: 3629
Check Sum: 0x1337659F

1.    Change 5G SSID back to the same as v1.01 (dlink-media-xxxx)
2.    HK DHCP issue
3.    fix iOS6 issue
4.    Change remote HTTPS management port from 8181 to 8090
5.    HW reset and wps button behavior

fix bugs:
pre-test
1.    wireless security EAP: DUT send out radius authenticator packet  need manual reboot. (ps: radius server at WAN site)
        Step1. Restore DUT to default.
        Step2. Setup wireless security to WEP key.
        Step2. Change wireless security to EAP.
        Step3. Change WAN connection mode from DHCP mode to static mode.
        Step4. Sniffer WAN site packet to check radius authenticator packet.
2.    DUT will be send out ARP reply when WAN site have PC send out ARP broadcast to query 192.168.0.1.
3.    TSD bug 15920 case2: DUT have uncanny DHCPv6 behavior after DUT dial-up pppoe, this bug base on TSD bug 15920 case2. Please refer the packet Q1.
4.    sometimes pppoe session disconnect because DUT not send out LCP echo reply to pppoe server. Please refer the packet Q2. (ps: reconnect mode is always on) (Cannot reproduce, please contact Vic if it happends)

TSD
16822    802.11a displayed as 802.11g in STATUS Wireless client list.
16562    "1. Routing using netmask 255.255.255.255 can be save, but unable to enable it. (Fixed)
            2. The 4th range of destination IP address should be allow 0~255. (1.00B21)"

===========================================================================================================================================
Date:2012-09-20
Firmware Version:v1.02B21
Kernel: Linux version 2.6.36
Source version: 3581
Check Sum: 0xAAD858C1

fix bugs:
pre-test
1. User can't login shareport web access web UI  from https.
2. TSD bug: IPv6 status cannot show WAN /DNS IPv6 address.-->display wrong default gateway at 6to4 mode, please refer the pic1.
3. 6RD sunset: DUT send out solicit message after DUT get IANA and IAPD already. Please refer the packet Q11.
4. 6RD sunset: sometimes DUT send out decline message but DUT not receive NA message. Please refer the packet Q12.
5. 6RD sunset: sometimes IPv6 status page display wrong IP information. Please refer the pic13-1, pic13-2.
6. 6RD sunset: valid time same with preferred time at RA information for 6RD.
7. 6RD sunset: routing table display issue. Please refer the pic14.
8. 6RD sunset: IPv6 connection mode should from 6RD sunset change to auto configure after user press release button at IPv4 status page.
9. 6RD sunset: 6RD tunnel still establish (because LAN site pc can ping to 6RD server) after user press release button at IPv4 status page.


TSD
16000    During BT test, DUT always reboot in random time.
16223    Shareport Mobile remote access log in page can enter "a" and admin passwords to log in storage as admin account.
16556    QRS mobile setting PPPoE mode, PPPoE Maximum Idle Time is 0 minutes, it should set as DUT default setting(5 minutes).
16228    Access Shareport Mobile remote page with no device, page will display error.
16562    Routing using netmask 255.255.255.255 can be save, but unable to enable it.
15887    Device name in Shareport Mobile Wizard not obey SPEC define.
15622    Windows Phone able connect, but not able show at 1.setup->network settings->Number of Dynamic DHCP Client 2.Status ->Lan Computers (DUT:Security Type - WPA2-AES)
15920    "DUT WAN connect to network with PPPoE and autoconfuguration server.
            Case1.
            Step1. Setup IPv4 connection mode to pppoe and check IPv6 detect to pppoev6 mode
            Step2. Setup  IPv4 connection mode to DHCP.
            Step3. Check IPv6 status page and check packet at WAN site.
            issue: After DUT IPv4 switching from PPPoE to DHCP mode, DUT IPv6 can¡¦t detect auto configure mode.
            
            Case2.
            Step1. Setup IPv4 connection mode to DHCP and check IPv6 Status page detect auto configure mode.
            Step2.  Setup  IPv4 connection mode to pppoe.
            Step3. Check IPv6 status page and check packet at WAN site.
            issue: After IPv4 switching from DHCP to PPPoE mode, DUT IPv6 will send out DHCPv6 confirm message on IPv6cp."

===========================================================================================================================================
Date:2012-09-08
Firmware Version:v1.02B20
Kernel: Linux version 2.6.36
Source version: 3504
Check Sum: 0x38FB9FF8

fix bugs:
pre-test
1. UNH1.7: solicit interval issue. please refer the pic1.
2. UNH1.7: sometimes SOL_MAX_RT option not work. Please refer the packet Q2.
3. UNH2.5 partB: sometimes DHCPv6 server not work. Please refer packet Q3.
4. UNH2.9 partA/B: The CE-Router must not forward the ICMPv6 Echo Request from LAN to WAN when source address not being advertised by the CE-Router.
5. LAN site client can¡¦t access to wan site.
        Step1. DUT get IP address from WAN.
        Step2. Wan site RA server send out lifetime=0 at RA message.
        Step3. Wan site RA server send out lifetime=150 at RA message.
        Step4. LAN site client ping to WAN site
6. Sometimes DUT send out wrong hint information. Please refer the packet Q6.
7. DUT will be release IAPD and IANA after DUT get RA message M=0, O=1 or M=1, O=0.
8. DUT will be release IAPD and IANA after DUT get RA lifetime=0.
9. Ingress Filtering function should be enable at default

TSD
0015465    IPv6 status cannot show WAN /DNS IPv6 address.
0016258    Firmware update 0kb file will cause web service crash.
0015785    PPPoE clients don't terminate the existing PPPoE session after several LCP Echo-Requests have failed. (Behavior is different with DIR-653 A1)

===========================================================================================================================================
Date:2012-08-31
Firmware Version:v1.02B19
Kernel: Linux version 2.6.36
Source version: 3464
Check Sum: 0x2E38DC3D

Please test BT

Fix bugs:
pre-test
1. auto detect: DUT can¡¦t detect auto configure mode. Please refer the packet Q1.
        Step1.  Setup IPv4 connection mode to pppoe and check IPv6 detect to pppoev6 mode
        Step2.  Setup  IPv4 connection mode to DHCP.
        Step3. Check IPv6 status page and check packet at WAN site.
2. auto detect: DUT will send out confirm message on IPv6cp. Please refer the Q2.
        Step1.  Setup IPv4 connection mode to DHCP and check IPv6 detect to auto configure mode.
        Step2.  Setup  IPv4 connection mode to pppoe.
        Step3. Check IPv6 status page and check packet at WAN site.

TSD
15887    Device name in Shareport Mobile Wizard not obey SPEC define.
15622    Windows Phone able connect, but not able show at 1.setup->network settings->Number of Dynamic DHCP Client 2.Status ->Lan Computers (DUT:Security Type - WPA2-AES)
15920    "DUT WAN connect to network with PPPoE and autoconfuguration server.
            Case1.
            Step1. Setup IPv4 connection mode to pppoe and check IPv6 detect to pppoev6 mode
            Step2. Setup  IPv4 connection mode to DHCP.
            Step3. Check IPv6 status page and check packet at WAN site.
            issue: After DUT IPv4 switching from PPPoE to DHCP mode, DUT IPv6 can¡¦t detect auto configure mode.
            Case2.
            Step1. Setup IPv4 connection mode to DHCP and check IPv6 Status page detect auto configure mode.
            Step2.  Setup  IPv4 connection mode to pppoe.
            Step3. Check IPv6 status page and check packet at WAN site.
            issue: After IPv4 switching from DHCP to PPPoE mode, DUT IPv6 will send out DHCPv6 confirm message on IPv6cp."
            

===========================================================================================================================================
Date:2012-08-17
Firmware Version:v1.02B18
Kernel: Linux version 2.6.36
Source version: 3340
Check Sum: 0x503428D4

1. fix Unable to Disable Guest Zone
2. fix RTK switch can¡¦t send v6 RS packet problem.

Fix bugs:
pretest
1. IPv6 auto detection mode: DUT can¡¦t detect pppoev6 mode and IPv6 status page display autoconfig mode when WAN site is hinet pppoev6 environment.

TSD
15795 Port forwarding and remote management port conflict issue
===========================================================================================================================================

Date:2012-08-15
Firmware Version:v1.02B17
Kernel: Linux version 2.6.36
Source version: 3318
Check Sum: 0x8BB7C2F7

Fix bugs:
pretest
1. IPv6 routing NULL interface do not work.
2. Inbound filter warning message uncertainty when entering incorrect IP address in Remote IP end then clicks "Add" or ¡§Update" button.

TSD
11404 QoS help page issue
15730 PPPoE MAC clone issue

===========================================================================================================================================

Date:2012-08-10
Firmware Version:v1.02B16
Kernel: Linux version 2.6.36
Source version: 3280
Check Sum: 0x3BDF0944

Fix bugs:
pretest
1. IPv6 status cannot show IPv6 DNS address.
2. Trigger v4 PPP session again,  Result IPv6 also be triggered.
3. GUI cannot open when WAN cable plug-in and username/PW incorrect in PPPoE/PPTP/L2TP
4. IPv6 routing NULL interface do not work.
5. ¤W¶g¤­·|ij¤WD-Link­n¨DªºDNS queries mydlink.com ©ñ¦b²Ä¤@­Ó
6. Step1. DUT restore to default.
    Step2. Set IPv6 static(use link-local) by IPv6 wizard.
    Result IPv6 status WAN link-local prefix is incorrectly.It should be 64.
7. Inbound filter warning message uncertainty when entering incorrect IP address in Remote IP end then clicks "Add" or ¡§Update" button.
8. Web access category content are blank if input over 200G file in storage device.
9. Web Files access UI cannot open URL.
10. "Step1. DUT restore to default.
     Step2. Set IPv6 static(use link-local) by IPv6 wizard.
      Result IPv6 status WAN link-local prefix is incorrectly.It should be 64."

TSD
15715    IPv6 Auto Detection GUI issue
15660    Setup wizard test
15651    Guest zone
15647    Wireless status issue
15625    GUI can not open issue
15558    Mydlink GUI issue
15538    Virtual server port conflict between rules issue
15465    IPv6 status
15373    IPv6 wizard with static issue
15267    Shareport web access link without dynamic dns
15138    IPv6 autodetection/autoconfiguration/pppoe  DNS query issue
15121    Mac address filter issue
14951    IPv6 routing Null interface issue
11919    Shareport - Traditional Chinese display issue (USB format is FAT and FAT32)
11287    Advanced-Advanced Network-UPnP
15643    BT test reboot issue

===========================================================================================================================================

Date:2012-07-30
Firmware Version:v1.02B15
Kernel: Linux version 2.6.36
Source version: 3184
Check Sum: 0x5FDAEF67

1. Fixed L2TP issue.
2. LAN PC can response WAN site PC ICMPv6 echo request when DUT disable "WAN ping respond".DUT should not response WAN site PC access to DUT LAN/WAN interface.

===========================================================================================================================================

Date:2012-07-30
Firmware Version:v1.02B14
Kernel: Linux version 2.6.36
Source version: 3170
Check Sum: 0x81E01626

Fixed TSD bugs:
1."1.DUT restore to default.
2.Disable LAN PC IPv6 protocol.
3.Set v4 mode to PPPoE on demand.
4.Set v6 mode to PPPoE on demand.
5.WAN cable link to PPPoE server.
6.Trigger v4 PPP session.(make sure IPv4 PPP session is established.)
7.Manual reboot DUT.
8.Trigger v4 PPP session again.
Result IPv6 also be triggered."
2."1.DUT restore to default.
2.Disable LAN PC IPv6 protocol.
3.Set v4 mode to PPPoE on demand.
4.Set v6 mode to PPPoE on demand.
5.WAN cable link to PPPoE server.
6.Trigger v4 PPP session.(make sure IPv4 PPP session is established.)
Result IPv6 status show connection up time."
3.IPv6 DSLite mode, ping DUT LAN from AFTR server with no reply.
4."1.DUT restore to default.
2.Disable LAN PC IPv6 protocol.
3.Set v4 mode to PPPoE on demand.
4.Set v6 mode to PPPoE on demand.
5.WAN cable link to PPPoE server.
6.Trigger v4 PPP session.(make sure IPv4 PPP session is established.)
7.Manual reboot DUT.
8.Trigger v4 PPP session again.
Result IPv4 PPP session is established too slow."
5."1.Restore default
2.Disable True Gigabit Routing Connectivity function.
3.Enable QOS or SPI function.
4.Disable QOS and SPI function.
issue: True Gigabit Routing Connectivity will be enabled automatically."
6."1.Admin can not open device.
2.Shareport device display incorrect in Android shareport mobile.
Test environment: HTC Sensation with Android 4.0.3 and Samsung Galaxy Note with Android 2.3.6."
7.Web access category content are blank if input over 200G file in storage device.
8.User named include "\" will cause account can not modify access path.
9.DS-Lite status cannot show AFTR address and connection up time.
10.When connect with no storage device, user account can open edit window in Storage setting page but only "cancel" button can click, suggest inform user more specific information like DIR-857.
11.Reset WPS PIN to default, display " in GUI and could be saved.
12.WPS hardware button need to push twice then active at the first time using WPS PBC function.
13."When ¡§Routing Between Zone¡¨ is NOT enabled.Guest zone users  
1.Can access usb storage via Web file access.
2.Can access usb storage via Samba.
  

"
14.Wireless clients often can not receive multicast stream. After disable True Gigabit Routing Connectivity function in Setup-Internet, wireless client can get multicast stream packets without problem.
15.Schedule rule list time format always display 24-hour format even select 12-hour format.
16."Some support page no function content.
1.) Storage
2.) IPv6 Firewall Rules
3.) IPv6 Routing
"
17."Step1. DUT restore to default.
Step2. Set IPv6 static(use link-local) by IPv6 wizard.
Result IPv6 status WAN link-local prefix is incorrectly.It should be 64."
18.Setting inbound filter rule, entering incorrect IP address or empty rule name then click ""Add"" or Update"" to create or update inbound filter rule, GUI will popup warning message, then ""Add"" or Update"" button been gray out.
issue: User can not add or edit filter rules if entering incorrect data."
19."1.Admin can not open device.
2.Shareport device display incorrect in Android shareport mobile.
Test environment: HTC Sensation with Android 4.0.3 and Samsung Galaxy Note with Android 2.3.6."
20.DDNS server address default is "dlinkddns.com", it's different in select bar "dlinkddns.com(Free)".
21.Lack of priority information in STATUS-Internet Sessions page for testing QOS function.
22.IPv6 status show incorrect ipv6 address on IPv6 static PPPoE mode.
23.IPv4 Multicast Streams disabled, clients can receive multicast stream still.
24.Wireless client with static IP address out of DHCP IP range not display in status wireless clients list.
25.Guest zone clients can not resolve DNS and access internet, even can not get ICMP response from DUT.
26.DS-Lite tunnel cannot be established when IPv6 type is auto configuration.
27."Step1.Modify DUT LAN IPv6 address to e.g. 3000:aaaa:bbbb:cccc::1 in IPv6 static type.
Step2.Change IPv6 type to autodetect(make sure DUT get LAN IPv6 address automatically).
Step3.Manual reboot DUT.
Result LAN side PC still get 3000:aaaa:bbbb:cccc:: network segment address."
28.1.Enable Virtual Server any rules.
2.Enable Storage function then save.
issue: GUI always pop up ""Remote Access Port ports conflicts with other setting"" message no matter change to any port and can not enable Storage function."
29.When sending shareport web access link without dyndns,then we could found the mail included the hyperlink of dyndns.
30.Input character or the same port as http in https port field then save, DUT should not allow saving. Suggest popup warning message to prevent users saving the incorrect settings.
31.Shareport Access Port can not be changed.
32.WAN site PC2 cannot access to LAN PC when 6to4 connection is established.
33."1.Change IPv6 Firewall parameters to Turn IPv6 Firewall ON and DENY rules listed.
2.Add a schedule 18:00-18:10
3.Manual set DUT time to meet the schedule.
4.Enter a firewall rule:
shchedule 18:00-18:10
From WAN side 2001:aaaa:bbbb:cccc:1111:2222:3333:64 to LAN

side 3000 :aaaa :bbbb :cccc ::a001 Protocol:ANY Result WAN server2(centos

2001:aaaa:bbbb:cccc:1111:2222:3333:64) can get ICMPv6 reply from LAN PC3(3000 :aaaa :bbbb

:cccc ::a001). "
34.IPv6 status cannot show IPv6 DNS address.
35.LAN PC can not get IPv6 address in 6in4 mode.RA life time is always zero.
DUT have no LAN side routing on 6in4 type.(Attach DUT config)
36.Since 6to4 relay address change to domain name "6to4.ipv6.microsoft.com" ,LAN PC cannot access ipv6 site via "6to4 relay server".
37.IPv6 routing NULL interface do not work.
38.LAN PC can response WAN site PC ICMPv6 echo request when DUT disable "WAN ping respond".DUT should not response WAN site PC access to DUT LAN/WAN interface.
39.Open shareport web page in IE8 with error.

Fixed UNH bugs:
1. UNH1.1 partB: DUT send out RS message to do DAD after DUT get RA message.
2. UNH2.1 partB: DAD failed. Please refer packet file Q2.
3. UNH1.3 partA: IPv6 status page still display expired global IP address.
4. UNH2.6 partA: DUT send out RA message with old prefix after DUT send out lifetime=o at RA message with old prefix and DUT send out lifetime=o at RA message with new prefix before send out RA message with new prefix. Please refer packet file Q4.
5. UNH2.7 partA: DUT not send out toobig message. Please refer packet file Q5.
6. DUT not send out RA message with lifetime=0 at LAN site after user press release button at IPv6 status page.


===========================================================================================================================================

Date:2012-07-18
Firmware Version:v1.02B13
Kernel: Linux version 2.6.36
Source version: 3048
Check Sum: 0x8B43A7DC

Fixed pretest bugs:
1. wireless security WPA/WPA2 EAP not work after DUT reboot.
2. QRS mobile pro.
2.1 Wireless 2.4G Settings always display disable from iOS QRS Mobile Pro.
2.2 Guest Zone set failure from QRS Mobile Pro.
2.3 QRS Mobile Pro be closed:
    2.3.1.  When Web File Access saved from Android QRS Mobile Pro.
    2.3.2.  When SharePort select directory from QRS Mobile Pro.
    2.3.3.  When MAC Filter enable first from iOS QRS Mobile Pro.
    2.3.4.  When Web File Access deleted account from Android QRS Mobile Pro.
2.4 Add SharePort account failure from QRS Mobile Pro.
2.5 App connected failure from Android QRS Mobile Pro when select Wi-Fi/Admin/Parental Control.

===========================================================================================================================================

Date:2012-07-13
Firmware Version:v1.02B12
Kernel: Linux version 2.6.36
Source version:  2996
Check Sum: 0x8F01730F

Fixed pretest bugs:
1. auto detection (flow setup6): sometimes IPv6 status page not display DNS information and RA message not have DNS information. Please refer FW102B08 the packet file Q3. (ps: hinet pppoev6 environment)
Step1. DUT detect to pppoe mode.
Step2. press disconnect button at IPv6 status page.
Step3. press connect button at IPv6 status page.
Step4. un-plug WAN port cable.
Step5. plug wan port cable.

===========================================================================================================================================

Date:2012-07-11
Firmware Version:v1.02B11
Kernel: Linux version 2.6.36
Source version: 2968
Check Sum: 0x1400683F

Please test:
1. QRS mobile pro

Fixed pretest bugs:
1. (Cannot reproduce) auto detection (flow setup6): sometimes IPv6 status page not display DNS information and RA message not have DNS information. Please refer FW102B08 the packet file Q3. (ps: hinet pppoev6 environment)
Step1. DUT detect to pppoe mode.
Step2. press disconnect button at IPv6 status page.
Step3. press connect button at IPv6 status page.
Step4. un-plug WAN port cable.
Step5. plug wan port cable.

===========================================================================================================================================

Date:2012-07-03
Firmware Version:v1.02B10
Kernel: Linux version 2.6.36
Source version: 2880
Check Sum: 0x0CAAA9ED

Please test:
1. IPv6 fixed bugs
2. WAN/LAN/WiFi/Samba throughput

Fixed pretest bugs:
1. auto detection (flow setup6): sometimes DUT detect to pppoev6 mode success but DUT send out RA lifetime=0 at LAN site. Please refer the packet file Q4. (ps: hinet pppoev6 environment)
Step1. DUT detect to pppoe mode.
Step2. press disconnect button at IPv6 status page.
Step3. press connect button at IPv6 status page.
Step4. un-plug WAN port cable.
Step5. plug wan port cable.

===========================================================================================================================================

Date:2012-07-03
Firmware Version:v1.02B09
Kernel: Linux version 2.6.36
Source version: 2868
Check Sum: 0xDAF9489D

Please test:
1. IPv6 fixed bugs
2. win7 logo
3. Setup wizard: new internet connection detection policy before mydlink setup

Fixed pretest bugs:
1. DUT detect to autoconfiguration (flow setup5): DUT still send out solicit message on IPv6CP after DUT detect autoconfig mode already. Please refer the packet file Q1.
2. auto detection (flow setup6): sometimes IPv6 status page display autoconfig mode and send out RA lifetime=0 at LAN site. Please refer the packet file Q2. (ps: hinet pppoev6 environment)
Step1. DUT detect to pppoe mode.
Step2. press disconnect button at IPv6 status page.
Step3. press connect button at IPv6 status page.
Step4. un-plug WAN port cable.
Step5. plug wan port cable.
3. auto detection (flow setup6): sometimes IPv6 status page not display DNS information and RA message not have DNS information. Please refer the packet file Q3. (ps: hinet pppoev6 environment)
Step1. DUT detect to pppoe mode.
Step2. press disconnect button at IPv6 status page.
Step3. press connect button at IPv6 status page.
Step4. un-plug WAN port cable.
Step5. plug wan port cable.
4. auto detection (flow setup6): sometimes DUT detect to pppoev6 mode success but DUT send out RA lifetime=0 at LAN site. Please refer the packet file Q4. (ps: hinet pppoev6 environment)
Step1. DUT detect to pppoe mode.
Step2. press disconnect button at IPv6 status page.
Step3. press connect button at IPv6 status page.
Step4. un-plug WAN port cable.
Step5. plug wan port cable.

===========================================================================================================================================

Date:2012-06-26
Firmware Version:v1.02B08
Kernel: Linux version 2.6.36
Source version: 2825
Check Sum: 0xAA714784

Fixed pretest bugs:
1. DUT detect to autoconfiguration (flow setup5): DUT re-dial pppoe before the DUT send out RS message.
2. IPv6 connection type show Auto Detection when press Disconnect then Connect button to reconnection on IPv6 status.

===========================================================================================================================================

Date:2012-06-26
Firmware Version:v1.02B07
Kernel: Linux version 2.6.36
Source version: 2816
Check Sum: 0x0EDEB648

Fixed pretest bugs:
1. DUT detect to pppoev6 (flow setup6): IPv6 status page display autoconfiguration.
Step1. DUT detect to autoconfiguration
Step2. Setup IPv4 connection type from DHCP to pppoe and save setting.
Step3. Check detection mode at IPv6 status page.
2. DUT detect to autoconfiguration (flow setup5): DUT not send out solicit message after DUT receive RA.

===========================================================================================================================================

Date:2012-06-21
Firmware Version:v1.02B06
Kernel: Linux version 2.6.36
Source version: 2771
Check Sum: 0xD31C6488

Please test:
1. IPv6 until 2.01R
2. USB throughput
3. Unlock IGMP management IP

Fixed pretest bugs:
1. DUT detect to DS-lite (flow setup4): sometimes status page not display AFTR-address and LAN site client get destination unreachable message when ping to IPv4 remote site.
2. DUT detect to pppoev6 (flow setup6): IPv6 status page display autoconfiguration.
Step1. DUT detect to autoconfiguration
Step2. Setup IPv4 connection type from DHCP to pppoe and save setting.
Step3. Check detection mode at IPv6 status page.
3. DUT detect to autoconfiguration (flow setup5): DUT not send out solicit message after DUT receive RA.
4. DUT detect to dhcpv6 (flow setup3): IPv6 status page not display wan IP address after DUT send out confirm message.
5. DUT can¡¦t pop ¡§no internet detected¡¨ message when DUT wan interface have IP address (ppp) but can not access to internet.

===========================================================================================================================================

Date:2012-06-11
Firmware Version:v1.02B05
Kernel: Linux version 2.6.36
Source version: 2722
Check Sum: 0x067512DA

Please test:
1. IPv6 2.01
2. UNH-IOL
3. PPTP/L2TP throughput
4. USB throughput

Fixed pretest bugs:
1. DUT detect to DS-lite (flow setup4):: The DS-lite tunnel can not be establish.
2. DUT detect to DS-lite (flow setup4):: DUT should not judged as ¡§DS-lite¡¨ mode if DNS not reply DS-lite server address (option 64).
3. DUT detect to pppoev6 (flow setup6): DUT can¡¦t get DNS address from pppoev6 server (hinet).
4. DUT detect to autoconfiguration (flow setup5): pppoe can¡¦t get IPv4 address because DUT unending redial to pppoe server if DUT not recive RA and DHCP-PD on IPv6CP.
5. DUT detect to autoconfiguration (flow setup5): DUT not send out RS for autoconfiguration after DUT not recive RA and DHCP-PD on IPv6CP.
6. DUT detect to dhcpv6 (flow setup3): DUT can¡¦t send out confirm message after re-plug wan cable. (RA server M flag=1)
7. DUT detect to dhcpv6 (flow setup2 and setup3): sometimes IPv6 release button not work. (RA server M flag=1 or M flag=0, A flag=1)
8. mydlink: DUT should redirect web page to http://www.mydlink.com after setup wizard finish, not redirect to http://www.mydlink.com/entrance.
9. sometimes DUT pop ¡§no internet detected¡¨  when run web base setup wizard. (ps: IE9)
10. internet LED to shone orange light after DUT connected to PPTP server
11. 2.6 part a: after WAN site server change IAPD, DUT have send out RA lifetime=0
and preferred lifetime=0 by old PD at LAN site but DUT will be kill new PD
(please check packet at LAN site).

===========================================================================================================================================

Date:2012-06-11
Firmware Version:v1.02B04
Kernel: Linux version 2.6.36
Source version: 2663
Check Sum: 0xBFD6A24D

Please test:
1. IPv6 2.01

Fix pretest bugs:
1. DUT will be send out wrong interval time of solicit message and wrong hint information after DUT send out rebind message.
2. The interval  time is too short of RA message send out when DUT wan cable disconnect.
3. PPPoE reconnect mode be set manual after Default Setup Wizard set step6 Mydlink. So Internet is disconnected.
4. GUI not next action when press Login button at Step 6: Mydlink page via Setup wizard and register mydlink account success.
5. Guest zone users cannot open DUT webpage when Routing Between Zone is enabled. But guest clients can open webpage after DUT reboot.
6. DUT send out RA lifetime=0 at LAN site after DUT do DAD for GLA.
7. IPv6 Auto detection: User login web UI get ¡§500 internal error¡¨ at firefox/IE when IPv6 connection mode at auto detection mode. Please refer pic1. (ps: wan site environment is DHCPv6.)
8. IPv6 Auto detection: DUT abnormal release IPv6 address when IPv6 connection mode at auto detection mode. Please refer pic2 (ps: wan site environment is DHCPv6.)


===========================================================================================================================================

Date:2012-06-01
Firmware Version:v1.02B03
Kernel: Linux version 2.6.36
Source version: 2633
Check Sum: 0xB6EECA91

Please test:
1. IPv6 2.01R
2. UNH-IOL
3. wifi mld snooping

Fix preteset bugs:
1. ULA DAD failed.
2 .1.3 part b: IPv6 status page display WAN IP prefix length=0.
3. 1.4 part b: DUT send solicit message after DHCP server reply (status code 0) to DHCPv6 confirm message.
4. DUT send out DHCPv6 confirm message when press renew button.
5. DUT send out strange solicit message after send out rebind message. Please refer packet.
6. 2.3 part b: CE-Router must transmit Router Advertisements with a router lifetime of zero on LAN1.
7. 2.3 part d: CE-Router must transmit Router Advertisements with a router lifetime of zero on LAN1.
8. 2.7 part a: DUT not send out too big message.
9. Guest zone users can not access USB storage via Web File Access when Routing Between Zone is enabled, but via Samba can access. Jerry fixed
10. IOT: user can¡¦t used WPS to connect with DUT when used D-Link UI.  (D-link DWA160 A1 v1.80) fixed(WPS UUID 2.4G/5G overlap)

Fix TSD bug:
12416    Sometimes after DUT restore to default, clients ping to URL with no response. But success in system check.
    1.DUT restore to default.
    2.Cancel wizard.
    3.Modify SSID and password.
    4.Save settings and plug out wire cable.
    5.Connect wireless client to DUT.

===========================================================================================================================================

Date:2012-05-25
Firmware Version:v1.02B02
Kernel: Linux version 2.6.36
Source version: 2594
Check Sum: 0x205E02D4

Please test:
1. IPv6 2.01R
2. UNH-IOL

Fix preteset bugs:
1. DUT wireless security mode be set WPA-Auto(WPA/WPA2) mixed(TKIP and AES) after Windows WCN configured None or WPA2-AES.
2. sometimes Win7 WPS icon cannot be discovered in Network folder after setup DUT to unconfigured. (setup to unconfig from web UI„³setup to config from win7 WPS icon„³ setup to unconfig from web UI„³check at win7 Network folder)
3. Port conflict not pop warning message; like: Shareport HTTP set 8181, Admin remote management set 8181.
4. Shareport Wizard: Chrome browser cannot scroll browser when select storage path.
5. Shareport Wizard: DDNS host name only just can key 15 characters at Shareport wizard.
6. Delete icon should be hidden when Access Path is None in Storage User List.
7. Account [Admin]/[Guest] cannot login to Shareport web access, but used [admin]/[guest] can.
8. Unplug USB device occur GUI crash, and DUT cannot open GUI. (HTTP)
9. Ports field can saved when key 079990 in Port Forwarding setting page
10. GUI still show No Internet detected when Setup Wizard checking WAN connectivity, but client can access Internet and ping DNS. Ps WAN type used PPPoE
11. GUI show warning message about Storage remote access when add user account in Storage page if disable allow remote access.
12. Guest zone users can not access USB storage via Samba when Routing Between Zone is enabled, but Web File Access GUI can access.

Fix TSD bugs:
11819    DUT2 IPv6 client list is incorrectly when client DUT1 is static ipv6 type.
12117    6rd cannot work when 6rd Border relay ipv4 address use FQDN.
13134    DUT LAN side RA router lifetime values do not set to zero when manual click reboot button.

===========================================================================================================================================

Date:2012-05-14
Firmware Version:v1.02B01
Kernel: Linux version 2.6.36
Source version: 2424
Check Sum: 0xCAAF3D98

Please test:
1. Win 7 logo
2. UNH-IOL test plan 1.00b06
3. USB IOT (3T storage)
4. SharePort Mobile name sorting in category view

Fix TSD bugs:
11196    "When WIN7 OS use wire(cable) to connect DUT, it cannot be discovered in Network folder or disappear for a some time. (DUT in unconfigured mode) "
11287    "Test Steps:
            1.Restore DUT to Factory Default
            2.Configure WAN type as PPPoE
            3.Enable UPnP at DUT Web UI.
            4.Launch the My Network Places, press F5 function key for scanning UPnP devices.
            5.Enable FTP at PC(OS : Windows XP) ""Internet Gateway""
            
            Test Result: Can't Enable FTP by ""Internet Gateway"" by PC"
        11713    The IPv6 connection information wording is wrong.
        11755    AFTR IPv6 address format should be "2001:1::1".
        11860    "Notice of firmware upgrade HTTP string is incorrectly.(Attach WAN packets.) "
        11964    There will be a warning message for a script cause Web GUI can't be displayed at IE6
        12151    "Enable other machine for one policy will apply to all machines.
        Test Step as below,
        Step 1. Restore DUT to factory default
        Step 2. Setup DUT by manual (Don't setup by Web-Base Wizard)
        Step 3. Configured WAN type as PPPoE, Reconnect-Mode:Always on
        Step 4. Configured Website filter, select ""ALLOW computers access to ONLY these sites"" and input ""yahoo"" and ""google"" in Website URL/Domain list
        Step 5. Enable policy in ""Access Control"" -
                Policy name ""TestA"", schedule ""Always"", Address type ""IP Address"" for PC1, Method: Log Web Access Only
                Policy name ""TestB"", schedule ""Always"", Address type ""Machine Address"" for PC2, Method: Block Some Access and Select ""Apply Advanced Port Filters"", Enable block TCP port 21
                Policy name ""TestC"", schedule ""Always"", Address type ""Other Machines"" for another PCs (PC3), Method: Block Some Access and Select ""Apply Web Filter"", then ""Enable"" Web Access Logging
        Step 6. Try to connect to ftp server and aceess websites at all LAN PCs
        
        Test result: Policy ""TestA"" and Policy ""TestB"" could work. But Policy ""TestC"" apply to PC2 with website filter and Web Access Logging. The Policy ""TestC"" shouldn't apply to Policy ""TestA"" and ""TestB"" PCs."
12172    When select the filtering method as "Block All Access" or "Port Filter" for "Block Some Access", the rule "Logged" display "Yes" in Policy Table. But check the syslog page, it didn't display any access log from apply filter machines.
12238    LAN PC cannot access WAN PPPoE server when manual set DUT LAN IPv6 address.(Attach WAN/LAN packets,DUT config,IPv6 routing table)
12239    IPv6 status page cannot show DUT LAN IPv6 address when manual set DUT LAN IPv6 address.
12319    Disable ALG PPTP, LAN PCs can't connect to VPN server.It should allow VPN clients connect to different VPN Servers as the description in support menu.
12348    DUT WAN side IPv6 address cannot show correct static PPPoE IPv6 address.
12354    DUT2 LAN PC cannot ping to WAN side server.DUT1 LAN side firewall rule should  set prefix 54.(Attach log image)
12383    "Enable Web File Access and HTTP Storage Remote Access,should not allow user access with HTTPS.
        Enable Web File Access and HTTPS Storage Remote Access,should not allow user access with HTTP.
        Enable Web File Access,should not allow user access with HTTP and HTTPS."
12385    USB device name should follow SPEC.
12450    Mydlink/DUT cannot block IPv6 client access internet.
12507    "Step1.DUT restore to default.
        Step2.WAN interface link to dhcp server.
        Result connection up time recount about 30min automatically."
12593    Input character or the same port as http in https port field then save, DUT should not allow saving.
12601    No matter mydlink service registered or not, click "Save Settings" in GUI mydlink setting page will cause web page error in IE.
12606    Manual uplink speed can be fit in letters and saving.
12609    Port filtering rules in access control can be saved as blank rule names and fit letters in port fields then saving.
12630    Click "Add" button many times to add inbound filter rule, same rule will be add may times in rule list.
12632    Often popup warning message when open virtual server setting page in IE6.
12660    Device name not obey the spec.
12662    Include not exist function in support page.
12690    When select Broadcast only in NetBIOS node type, WINS IP Address field should be gray out.
12697    Email log time not same as log time in DUT.
12736    Fail to connect wireless clients to DUT through PBC method in Wi-Fi Protected Setup GUI page.
12741    "1.Restore DUT default
        2.Disable 2.4GHz wireless band
        3.Connect wireless client to DUT 5GHz band through WPS
        issue:
        1.After connection established, 2.4GHz SSID will be changed the same to 5GHz band.
        2.Sometimes clients can not get IP address. (wireless adapter : DWA-160A1)"
12755    Wireless clients can not receive multicast stream.
12785    After click "Login" button in login page, GUI redirect to login page.
12804    Open GUI fail.
12810    "UPnP Negotiation : Blocked
        UPnP Required for NAT type : FAIL"
12819    WLAN PC cannot configure DUT wireless setting by Intel PROSet WPS_PIN code.
12832    Mydlink E-mail notification setting must be apart from the E-Mail setting in the Tool tab of Web UI.
12838    The open folder can't be closed.
12843    "When ¡§Routing Between Zone¡¨ is NOT enabled.Guest zone users  
        1.Can access usb storage via Web file access.
        2.Can access usb storage via Samba. "
12859    Set wireless 5GHz band channel 165, DUT display channel 36 in Status page.
12882    "Step 1.Plug in USB1(make sure you can access USB1 via samba ""sda1"".)
        Step 2.Change from USB1 to USB2.
        Result network appear 2 icon ""sda1"",""sdb1"" and the ""sda1"" cannot work."
12909    "1.Enable Virtual Server any rules.
        2.Enable Storage function then save.
        issue: GUI always pop up ""Remote Access Port ports conflicts with other setting"" message no matter change to any port and can not enable Storage function."
12918    Enable Storage function, before plug in usb storage device, edit user account will pop up gray out Append New Folder page. Suggest not allowing to edit account or other message for user, reference DIR-857 behavior as well.
12971    Input incorrect letter in port setting field then save, suggest to improve the warning message description more clearly.
12977    DUT WAN side interface have no send out PPP LCP termination request after click IPv6 status page disconnect button.
12979    DUT WAN interface have no send out PADI after LAN PC try to access internet IPv6 site.
13112    Can not visit GUI with "router.dlink.com" URL.
13126    Ports field can fit letters then save in Port Forwarding setting page.

===========================================================================================================================================

Date:2012-04-24
Firmware Version:v1.01B03
Kernel: Linux version 2.6.36
Source version: 2237
Check Sum: 0xDD727FF0

1. Fix wireless wizard password issue
2. Automatically enable ntp in setup wizard.

===========================================================================================================================================

Date:2012-04-23
Firmware Version:v1.01B02
Kernel: Linux version 2.6.36
Source version: 2234
Check Sum: 0x02AD6374

1. Fix WPS-PBC changing SSID issue, a bug that caused the 2.4G SSID and 5G SSID will be changed to be same
2. Modify wireless partition & guest zone.
3. USB multi-partition support for SharePort Mobile.

Fix TSD bug
12394     If the USB Storage has two partitions.The account added by user can't access the second partition. But login with admin the second partition can be accesse
Cita messaggio
#34
Qualcuno ha provato ad usare il blocco siti web di questo router?
Su altri modelli DIR funziona?
Cita messaggio
#35
In questo video esplicativo del canale YouTube Tutorials di D-Link Canada sembra funzionare per il DIR-826L A1 1.01.

Cita messaggio
#36
Question 
Salve a tutti questa è la mia ultima spiaggia senno credo di aver buttato 100euroSad, ho questo switch Wifi Dlink DIR-826L da 4 mesi e non capisco come si configura anche dopo aver sentito "diverse persone". Vi chiedo se qualcuno puo rispondermi con un tutorial dettagliato o per lo meno qualcosa che mi faccia capire come si configura con il modem di casa.
Ringrazio anticipatamente
buona serata
Francesco
Cita messaggio
#37
Ciao Francesco, non hai scritto le cose più importanti...
Marca e modello del modem?
Linea ADSL?
Cita messaggio
#38
ciao , si hai ragione perdonami.
il modem è uno speedtouch thomson ed a casa ho l'ADSL. Dopo svariati tentativi il problema che credo sia alla base di tutto è la configurazione tra lo switch ed il modem. Perchè non viene rilevata alcuna connessione internet ne in wifi da altri dispositivi ne dalla linea fissa.
Cita messaggio
#39
frann Ha scritto:il modem è uno speedtouch thomson
Quale? Di speedtouch ce ne sono moltissimi.

frann Ha scritto:ed a casa ho l'ADSL.
Operatore? Tiscali?
Cita messaggio
#40
allora lo speedtouch è un ST530 V6
ed il mio operatore è tele2 credo che ora si chiami TeleTu Smile
Grazie della considerazione
Cita messaggio


Vai al forum:


Utenti che stanno guardando questa discussione: 1 Ospite(i)