07-12-2016, 13:40 (Questo messaggio è stato modificato l'ultima volta il: 12-01-2019, 9:03 da Carciofone.)
D-Link DAP-1620 Range Extender compatto 1200AC
DAP-1620 Ax
Il D-Link DAP-1620 è un dispositivo compatto avente la duplice funzione di Range Extender Wireless 1200AC e di Access Point o punto di accesso da collegare mediante cavo ethernet direttamente ad un router o ad una presa cablata gigabit.
Il nuovo dispositivo si presenta, quindi, come un'unità estremamente versatile ed in grado di sopperire a molteplici esigenze, aumentando la copertura del segnale wireless fin nei luoghi più remoti ed inaccessibili della propria abitazione.
La velocità di trasmissione dati wireless è supportata in modalità AC fino a 1200 Mbps grazie alla tecnologia Dual-Band, mediante l'uso di entrambe le frequenze (2,4Ghz e 5 Ghz) al fine di garantire prestazioni migliori in caso si debbano gestire più connessioni contemporaneamente.
Il dispositivo è dotato di antenne ripegabili o estensibili,ed è caratterizzato da un indicatore a LED che segnala la posizione migliore in cui installare il dispositivo, in modo da ottenere la maggior estensione di rete possibile, senza ridurre la qualità del segnale. Tutti i Range Extender di D-Link assicurano la retrocompatibilità con i precedenti standard Wireless, senza che le prestazioni generali della rete ne risentano.
Il DAP-1620 può essere facilmente configurato tramite le App disponibili per IOS e Android o grazie alla configurazione guidata Set-up wizard per Windows o mediante il tasto unificato WPS (Wireless Protected System).
Specifiche tecniche
Interfacce del dispositivo
802.11ac/n/g/b/a Wireless LAN
10/100/1000 Gigabit Ethernet Port
Tasto Reset
Tasto WPS
LED
Status/WPS
Indicatore potenza segnale Wi-Fi a 3 led
Problem Resolved:
1. Power LED status is incorrect when uplink in link down and lan in static mode with lan cable connected.
2. Default wizard can't redirect to next step after connecting Ethernet to dhcp server for AP mode,
Problem Resolved:
1. Fixed LAN - Static IP - Incorrect DHCP Offer.
2. Fixed wireless should support 20Mhz only in ch12/ch13/ch140/ch165.
3. Fixed Sometimes user can't login when broswer prompt a message.
4. Fixed MAC address convert for wireless client in repeater mode is incorrect.
5. Fixed Invalid wps2-psk key should be blocked from wizard.
6. Fixed While input login password in Setup Wizard, the field is not masked with *.
7. Fixed GUI displays "checking.." only after clicking firmware check button.
8. Fixed uplink wireless will disconnected forever when click scan button below network icon .
9. Fixed wireless security key can be sniffered by CSRFteser.
10. Fixed DUT uplink fail after WPS-PBC link success via wizard when router with full 64 HEX.
11. Fixed Existing Network - WEP Authentication.
12. Fixed DUT can't recover to AP mode from configuration file.
13. Fixed DUT displays no new firmware after clicking firmware check ,but push F5 can display correctly.
Problem Resolved:
1. Fixed Repeater at Repeater can't work.
2. Fixed the LED of power can't stop blinking when do WPS-PBC for downlink in repeapter mode.
3. Fix always shows there is new firmware online
Enhancements:
1. Change the wireless driver to 3.0.4.0P1.
1. Fixed Physical WPS Button Behavior.
2. Fixed sometimes reboot fail issue.
3. Fixed dual uplink connected issue.
4. Fixed QRS mobile app can't detect DUT when no ethernet connected in default DUT
5. Fixed QRS mobile app can't detect DUT when no ethernet connected in default DUT
6. Fixed: Ping check issue after unplug cable from DUT.
7. Fixed dhcp server issue in DUT.
8. Fixed copy SSID/PWD fail when uplink router has full SSID via WPS-PBC of wizard.
Problem Resolved:
1. Fix DLINK CN Report Issue: base DAP-1620_A1_101B05????.xlsx
a. CN translation issue.
b. Admin password issue: clean password text when click the text, in Admin page.
c. Connect and disconnect string display error, in Home page.
d. Add the number of Connected Clients in Home page.
2. Follow spec "D-Link Extender Specification v1.03”.
a. Ethernet port detection behavior.
b. Wizard redirect behavior.
3. Follow spec DAP-1620 need copy SSID/PW and add –Ext after WPS connect success in web-based Setup Wizard.”
4. Fix the redirect to wizard not work, when use www.google.com in default state.
5. Fix MP issue: fix bulk can't send success when MP use bulk upgrade FW.
6. Fix CN translation issue in Network page.
Problem Resolved:
1. Power LED status is incorrect when uplink in link down and lan in static mode with lan cable connected.
2. Default wizard can't redirect to next step after connecting Ethernet to dhcp server for AP mode,
Problem Resolved:
1. Fixed LAN - Static IP - Incorrect DHCP Offer.
2. Fixed wireless should support 20Mhz only in ch12/ch13/ch140/ch165.
3. Fixed Sometimes user can't login when broswer prompt a message.
4. Fixed MAC address convert for wireless client in repeater mode is incorrect.
5. Fixed Invalid wps2-psk key should be blocked from wizard.
6. Fixed While input login password in Setup Wizard, the field is not masked with *.
7. Fixed GUI displays "checking.." only after clicking firmware check button.
8. Fixed uplink wireless will disconnected forever when click scan button below network icon .
9. Fixed wireless security key can be sniffered by CSRFteser.
10. Fixed DUT uplink fail after WPS-PBC link success via wizard when router with full 64 HEX.
11. Fixed Existing Network - WEP Authentication.
12. Fixed DUT can't recover to AP mode from configuration file.
13. Fixed DUT displays no new firmware after clicking firmware check ,but push F5 can display correctly.
Problem Resolved:
1. Fixed Repeater at Repeater can't work.
2. Fixed the LED of power can't stop blinking when do WPS-PBC for downlink in repeapter mode.
3. Fix always shows there is new firmware online
Enhancements:
1. Change the wireless driver to 3.0.4.0P1.
1. Fixed Physical WPS Button Behavior.
2. Fixed sometimes reboot fail issue.
3. Fixed dual uplink connected issue.
4. Fixed QRS mobile app can't detect DUT when no ethernet connected in default DUT
5. Fixed QRS mobile app can't detect DUT when no ethernet connected in default DUT
6. Fixed: Ping check issue after unplug cable from DUT.
7. Fixed dhcp server issue in DUT.
8. Fixed copy SSID/PWD fail when uplink router has full SSID via WPS-PBC of wizard.
Problem Resolved:
1. Fix DLINK CN Report Issue: base DAP-1620_A1_101B05????.xlsx
a. CN translation issue.
b. Admin password issue: clean password text when click the text, in Admin page.
c. Connect and disconnect string display error, in Home page.
d. Add the number of Connected Clients in Home page.
2. Follow spec "D-Link Extender Specification v1.03”.
a. Ethernet port detection behavior.
b. Wizard redirect behavior.
3. Follow spec DAP-1620 need copy SSID/PW and add –Ext after WPS connect success in web-based Setup Wizard.”
4. Fix the redirect to wizard not work, when use www.google.com in default state.
5. Fix MP issue: fix bulk can't send success when MP use bulk upgrade FW.
6. Fix CN translation issue in Network page.
Note:
1. Cannot connect extender to a router which has DHCP disabled.
2. Wifi password will change if I upload config file to different piece of DUT -> RESTORE DEFAULT -> CONFIG
3. After change management link, DUT won't redirect browser to new management link.
Specs: This policy is only for EU domain.
1. Repeater mode: Client interface support DFS channel and no channel option in extended AP UI.
PS: Always support DFS.
2. Access Point mode: Add DFS switch button in 5G setting page.
The status of DFS is “Enable”, channel option should grey out the DFS channels in options.
The status of DFS is “Disable”, channel option should remove the DFS channels in options.
PS: DUT need to record DFS setting value when change AP mode to Repeater mode.
Problem Resolved:
1. Power LED status is incorrect when uplink in link down and lan in static mode with lan cable connected.
2. Default wizard can't redirect to next step after connecting Ethernet to dhcp server for AP mode,
Problem Resolved:
1. Fixed LAN - Static IP - Incorrect DHCP Offer.
2. Fixed wireless should support 20Mhz only in ch12/ch13/ch140/ch165.
3. Fixed Sometimes user can't login when broswer prompt a message.
4. Fixed MAC address convert for wireless client in repeater mode is incorrect.
5. Fixed Invalid wps2-psk key should be blocked from wizard.
6. Fixed While input login password in Setup Wizard, the field is not masked with *.
7. Fixed GUI displays "checking.." only after clicking firmware check button.
8. Fixed uplink wireless will disconnected forever when click scan button below network icon .
9. Fixed wireless security key can be sniffered by CSRFteser.
10. Fixed DUT uplink fail after WPS-PBC link success via wizard when router with full 64 HEX.
11. Fixed Existing Network - WEP Authentication.
12. Fixed DUT can't recover to AP mode from configuration file.
13. Fixed DUT displays no new firmware after clicking firmware check ,but push F5 can display correctly.
Problem Resolved:
1. Fixed Repeater at Repeater can't work.
2. Fixed the LED of power can't stop blinking when do WPS-PBC for downlink in repeapter mode.
3. Fix always shows there is new firmware online
Enhancements:
1. Change the wireless driver to 3.0.4.0P1.
1. Fixed Physical WPS Button Behavior.
2. Fixed sometimes reboot fail issue.
3. Fixed dual uplink connected issue.
4. Fixed QRS mobile app can't detect DUT when no ethernet connected in default DUT
5. Fixed QRS mobile app can't detect DUT when no ethernet connected in default DUT
6. Fixed: Ping check issue after unplug cable from DUT.
7. Fixed dhcp server issue in DUT.
8. Fixed copy SSID/PWD fail when uplink router has full SSID via WPS-PBC of wizard.
Problem Resolved:
1. Fix DLINK CN Report Issue: base DAP-1620_A1_101B05????.xlsx
a. CN translation issue.
b. Admin password issue: clean password text when click the text, in Admin page.
c. Connect and disconnect string display error, in Home page.
d. Add the number of Connected Clients in Home page.
2. Follow spec "D-Link Extender Specification v1.03”.
a. Ethernet port detection behavior.
b. Wizard redirect behavior.
3. Follow spec DAP-1620 need copy SSID/PW and add –Ext after WPS connect success in web-based Setup Wizard.”
4. Fix the redirect to wizard not work, when use www.google.com in default state.
5. Fix MP issue: fix bulk can't send success when MP use bulk upgrade FW.
6. Fix CN translation issue in Network page.
ATTENZIONE: aggiunto al primo post il link per il download del nuovo firmware correttivo per l'ottimo range extender DAP-1620 v. 1.06B04 del 24.12.2017.
12-01-2019, 8:55 (Questo messaggio è stato modificato l'ultima volta il: 12-01-2019, 9:00 da Carciofone.)
ATTENZIONE: aggiunto al primo post il link per il download del nuovo firmware per il range extender DAP-1620 v. 1.02CLB08 del 07.08.2018 distribuito per le unità DAP commercializzate con marchio TIM.
L'installazione nelle unità generiche può avvenire solo mediante la procedura di recovery mode attivabile premendo e tenendo premuto il tasto di reset mentre si inserisce il DAP-1620 Ax nella presa della corrente e poi collegandosi mediante il cavo ethernet all'indirizzo 192.168.0.50 dopo aver impostato nella scheda di rete del PC l'IP fisso 192.168.0.10 Snmk 255.255.255.0.
L'upgrade dovrebbe garantire maggiore stabilità e compatibilità del dispositivo con le serie moderne di router Wireless AC.
sono riuscito ad avere una connessione WIFI AC con il mio router FriztBox solo aggiornando l'extender DAP-1620 "generico" con l'ultimo firmware TIM da te postato."solo tramite cavo ethernet"
GRAZIE DAVVERO adesso posso considerare funzionante questo dispositivo.
Ottimo!
In effetti aumenta molto l'usabilità, soprattutto del range extender usando la banda a 5 Ghz. Ricordate di impostare ilrouter principale AC con ampiezze di banda fino a 80 Mhz e non 160 Mhz, perchè a occhio il DAP 1620 supporta fino a 1200Mbps.
Ricordiamo anche che il repeater ha varie modalità di connessione configurabili con cui giocare nelle impostazioni.
In situazioni particolari si potrebbe scegliere di creare il bridge con il router principale con la rete a 5 Ghz più veloce, distribuendo poi attorno al repeater la banda con la sola modalità a 2.4 Ghz, oppure il contrario se si vuole privilegiare un'alta velocità di scambio tra i client connessi al DAP e avere comunque fino a 300 Mbit di collegamento con il router principale, ottimo se si hanno fibre fino a 200 Mbit.
In questi casi la radio a 2.4Ghz o 5 Ghz del repeater può essere disattivata migliorando incredibilmente la stabilità della connessione bridge wifi al router.
Se invece si hanno connessioni in fibra 1Gbps, ovviamente con dispositivi come questo bisogna scendere a compromessi a meno di non collegarli via cavo al router.
Un dispositivo potente come apparato wireless e velocità AC fino a 1900 che ho testato con funzioni di AP via cavo è il DIR-879.
(20-01-2019, 11:09)Carciofone Ha scritto: Ottimo!
In effetti aumenta molto l'usabilità, soprattutto del range extender usando la banda a 5 Ghz. Ricordate di impostare ilrouter principale AC con ampiezze di banda fino a 80 Mhz e non 160 Mhz, perchè a occhio il DAP 1620 supporta fino a 1200Mbps.
….
Concordo, anche secondo me se il router si attiva con canale di ampiezza 160 Mhz il DAP NON riesce a collegarsi.
uso una chiavetta wifi dlink dwa-182 sul computer in camera un extender dap-1620 con ultimo firmware Tim in corridoio e router fibra in salotto... l'extender è stato preso per avere 100% segnale sul 5g
purtroppo ho notato che il DAP si sconnette dal 5g del fritzbox 7530... : invece se uso il modem smart tim non ho nessuna disconnessione ma si connette in banda N fornendo comunque la banda fibra richiesta.
con il fritz ho provato sia con le reti 2g e 5g unificate che separate.... e si connette in banda AC ma con frequenti sconnessioni purtroppo
mentre con
smart modem telecom (tim) technicolor con wifi 2g 5g unificate il DAP non si sgancia manco morto ma si connette in banda N senza difficoltà e gestisce bene i dispositivi in cascata.
è un problema del fritz o di compatibilità dlink???
Purtroppo il 5G ha una portata veramente limitata in metri rispetto al 2.4Ghz. Se copre al massimo 10-12 metri, il repeater va messo al massimo a 4-6 m dal router perché funzioni bene ed estenda a sua volta per altri 6-10 m.
Poi sulla compatibilità avrei molto da dire: secondo me se un router sta funzionando con ampiezza di canale 80 o 160 Mhz il DAP-1620 che è un umile AC1200 non può reggerli perché significa che sul 5 Ghz è un 1200-300 (o 450?) e quindi viaggerà sui 40 Mhz massimo e quindi se il Fritz si setta su 160 Mhz non credo che i due comunichino. Ma aspetto conferme su questa mia idea.
Inoltre sono convinto che se gli 867 Mbps canonici dei 1200ac sono usati anche per diffondere il segnale a destinazione, alla fine sono divisi per il numero di cliet presenti, abbassando il link del collegamento al router in modo notevole: cioè un client in 5Ghz, link 433Mbps, due client più router, 289 Mbps e quindi siamo al pari o sotto di un 2.4Ghz con un solo client.
Per questo io ho pensato di usare il 2.4Ghz per il link al router e basta (la ripetizione della rete può essere disattivata) e poi il 5Ghz per diffondere il segnale a destinazione.
Oppure, se il collegamento regge e ancora meglio, il 5Ghz per fare il solo bridge con il router ad alta velocità e il 2.4Ghz per collegare a destinazione i client al DAP.
In questo modo riesco ad ottenere transfer rate wireless a 23m circa di distanza con il bridge a 70-114 Mbit da internet, di cui non mi lamento.
Non tutti i giorni il risultato è ottimale, ma va tenuto conto del fatto che la velocità del link dipende molto anche dalle condizioni atmosferiche trattandosi di un segnale radio.